Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Equipo de red - FS608v3 (738.03 kb)
Equipo de red - FS608v3 (135.71 kb)
Resumen del manual
With the Auto Uplink™ feature, you don’t have to worry about which one you use. Each port on the FS605 v3/FS608 v3 switch automatically configures itself correctly when you plug in a device’s cable. If you have a problem with your switch, NETGEAR offers free support 24 hours a day and 7 days a week on the Web (by e-mail (support@NETGEAR.com) and by phone (see the provided support information card for phone numbers). Installation Overview Estimated Time: 5–10 minutes 1. Unpack the box and verify the contents. 2. Prepare to install the switch. 3. Install the switch and connect the other devices. Unpack the Box and Verify the Contents Fast Ethernet Switch FS605 v3/FS608 v3 Installation guide, warranty/registration card Stand and support information card Power adapter When you open the box, verify that you received everything. The package includes: • 5/8-Port Fast Ethernet Switch FS605 v3/FS608 v3 • AC power adapter • FS605 v3/FS608 v3 Installation Guide (this document) • Warranty and support information card • Vertical stand If you don’t have everything listed above, see the support information card for contact information. If you’re missing the Technical Support information card itself, get contact information at in the Customer Service area. 2 22 Prepare to Install the Switch Decide where you want to place the switch. Find a flat horizontal surface — such as a table, desk or shelf. Make sure the selected location is: • Not in direct sunlight or near a heater or heating vent. • Not cluttered or crowded. There should be at least 2 inches (5 cm) of clear space on all sides of the switch. • Well ventilated (especially if it is in a closet). Also, you’ll need one Category 5 (Cat 5) Ethernet cable with RJ-45 connectors for each device you want to connect to the switch. Each Ethernet cable must be less than 328 feet (100 meters). Install the Switch and Connect the Other Devices Fast Ethernet Switch FS608 v3 RP614 4-Port Cable / DSL Router DSL modem 1. Place the switch on a flat surface using either the attached feet or the provided vertical stand. 2. For each device, insert one end of an Ethernet cable into the port in the device and insert the other end into one of the Ethernet ports on the switch. Note: If you have more than 5 or 8 devices to connect to this switch, you must connect them to a hub or other switch and then connect that hub or switch to this switch. 3. Connect the power adapter’s cord into the back of the switch and then plug the adapter into a power source (such as a wall socket or power strip). The Power light should light up. The corresponding port number for each connected and powered device should light when link (connection), and flash when activity occurs. Note: If any light doesn’t operate as indicated, go to the Troubleshootingsection. Troubleshooting The Power light is not lit The switch has no power. • Make sure the power cord is properly connected to the switch. • Make sure the power adapter is properly connected to a functioning power outlet. If it’s in a power strip, make sure the power strip is turned on. If the socket is controlled by a light switch, make sure the switch is in the on position. • Make sure you are using the NETGEAR power adapter supplied with your switch. The Port number light is not lit for a connected device or stays on continuously There’s a hardware connection problem. • Make sure the cable connectors are securely plugged in at the switch and the device. • Make sure the connected device is turned on. • If the Ethernet cable is connected to a NIC or other Ethernet adapter, make sure the card or adapter is installed correctly and is working. • Make sure the cable is less than 328 feet (100 meters). Technical Specifications Standards Compatibility: IEEE 802.3i 10BASE-T Ethernet, IEEE 802.3u,100BASE-TX Fast Ethernet IEEE 802.3x Flow Control; compatible with Windows®, Mac® OS, NetWare®, Linux® Data Rate: 100 Mbps with 4B/5B encoding and MLT-3 physical interface for 100BASE-TX 10 or 100 Mbps half-duplex Network Interface: RJ-45 connector for 10BASE-T or 100BASE-TX Ethernet interface DC Power: 7.5W max and 7.5V @1.0A DC inputt Physical Dimensions: FS605 v3 - W: 147mm (5.79") D: 96.7mm (3.81") H: 28.5mm (1.12") FS608 v3 - W: 171mm (6.73") D: 113.2mm (4.46") H: 28.5mm (1.12") Weight: FS605 v3 - 0.192kg (0.424 lbs); FS608 v3 - 0.278kg (0.614 lbs) Operating Temperature: 0 to 50° C (32 to 122° F) Operating Humidity: 10% t0 90% relative humidity, non-condensing Electromagnetic Compliance: CE mark, Commercial; FCC Part 15, Class B; EN 55 022 (CISPR 22) Class B, VCCI Class B, C-Tick Safety Agency Approvals for the Power Adapter: CE mark, Commercial UL listed (UL 1950), C-Tick Performance Specifications Frame Filter Rate: 14,800 frames/sec max for 10M port / 148,800 frames/sec max for 100M port Frame Forward Rate: 14,800 frames/sec max for 10M port / 148,800 frames/sec max for 100M port Network Latency: 100 Mbps to 100 Mbps: 20 .s max (using 64-b...