Votos - 1, Puntuación media: 4
(
)
)
|
Resumen del manual
rez 5 September 06 4673896 415s_281- 02_en_ d. rsc 440s_281- 02_en_ d. rsc 441s_281- 02_en_ d. rsc 442s_281- 02_en_ d. rsc 450s_281- 02_en_ d. rsc AR750S, AR750S- DP, AR770S 55281- 02. rez 5 September 06 3936164 750s_281- 02_en_ d. rsc (AR750S and AR750S- DP) AT- 8624T/ 2M, AT- 8624PoE, AT- 8648T/ 2SP AT- 8600 sr281- 02. rez 5 September 06 2251144 sr24_ 281- 02_en_d. rsc Caution: Using a maintenance version on the wrong model may cause unpredictable results, including disruption to the network. This maintenance release note should be read in conjunction with the following documents: ¦ the Release Note for Software Version 2.8.1, available from nz/ documentation/relnotes/relnotes. html ¦ your router or switch’s Document Set for Software Release 2.8.1. This document set is available on the CD-ROM that shipped with your router or switch, or from nz/documentation/documentation.html Caution: Information in this release note is subject to change without notice and does not represent a commitment on the part of Allied Telesis Inc. While every effort has been made to ensure that the information contained within this document and the features and changes described are accurate, Allied Telesis Inc. can not accept any type of liability for errors in, or omissions arising from the use of this information. Enabling and Installing this Release Enabling and Installing this Release To use this maintenance release you must have a base release license for Software Release 2.8.1. Contact your distributor or reseller for more information. To enable this release and install it as the preferred release, use the commands: enable rel= xx281- 02.rez num= 2.8.1 set install= pref rel= xx281- 02.rez where xx is the prefix to the filename, as shown in the table on page 1. For example, to install the release on an AR440S router, use the commands: enable rel= 54281- 02.rez num= 2.8.1 set install= pref rel= 54281- 02.rez Levels Some of the issues addressed in this Maintenance Version include a level number. This number reflects the importance of the issue that has been resolved. The levels are: Level 1 This issue will cause significant interruption to network services, and there is no work- around. Level 2 This issue will cause interruption to network service, however there is a work- around. Level 3 This issue will seldom appear, and will cause minor inconvenience. Level 4 This issue represents a cosmetic change and does not affect network operation. Version 281- 02 C613- 10482- 00 REV B Features in 281- 02 Features in 281-02 Software Maintenance Version 281-02 includes the resolved issues and enhancements in the following tables. In the tables, for each product series: ¦ “Y” in a white column indicates that the resolution is available in Version 281-02 for that product series. ¦ “-” in a white column indicates that the issue did not apply to that product series. ¦ a grey-shaded column indicates that Version 281-02 was not released on that product series. Level 1 CR Module Level Description AR400AR7x5AR750S / AR770SRapier iAT-8800AT-8600AT-8700XLAT-8948 / x900-48AT-9900AT-9800 CR00006040 PIM 6 1 For PIM on IPv6, if the interface that was being used as the BSR candidate address went down, the network occasionally did not re- elect a BSR and the RPs in a timely manner. This could cause the router or switch to reboot. This issue has been resolved. Y - Y - - - - - - - CR00007273 Switch 1 If a user created a configuration file that contained port trunk settings before VLAN port settings, then a loop occurred when the switch rebooted with this configuration. This issue has been resolved. - - - - - Y - - - - CR00013457 VLAN 1 When ports were added to a currently- disabled RSTP domain, the ports could start to discard packets ( because their STP state was set to Discarding) . This issue has been resolved. When ports are added to a disabled RSTP domain, they remain in a Forwarding state. - - - - - Y - - - - CR00013492 OSPF 1 When route filters ( made with the command add ip route filter) were used to filter OSPF routes, it was possible for OSPF to constantly remove and re-create an AS- External LSA. This could prevent OSPF sessions from establishing. This issue has been resolved. Y - Y - - Y - - - - Version 281- 02 C613- 10482- 00 REV B Features in 281- 02 CR Module Level Description AR400AR7x5AR750S / AR770SRapier iAT-8800AT-8600AT-8700XLAT-8948 / x900-48AT-9900AT-9800 CR00013736 Core 1 When a BRI or PRI PIC was installed on the router, an issue with internal memory handling occasionally caused the router to reboot. This issue has been resolved. Y - Y - - - - - - - CR00013743 Switch 1 If a user created a configuration file that contained LACP settings and VLAN port settings, then a loop occurred when the switch rebooted with this configuration. This issue has been resolved. - - - - - Y - - - - Level 2 CR Module Level Description AR400AR7x5AR750S / AR770SRapier iAT-8800AT-8600AT-8700XLAT-8948 / x900-48A...
Otros modelos de este manual:Equipo de red - AR750S-DP (144.62 kb)