Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Standardized jacks are used for these connections. This equipment should not be used on party lines or coin phones. 2. If this device is malfunctioning, it may also be causing harm to the telephone network; this device should be disconnected until the source of the problem can be determined and until repair has been made. If this is not done, the telephone company may temporarily disconnect service. 3. The telephone company may make changes in it's facilities, equipment, operation and procedures; if such changes affect the compatibility or use of this device, the telephone company is required to give adequate notice of the situation with the FCC. 4. If the telephone company requests information on what equipment is connected to their lines, inform them of: a. The telephone number to which this unit is connected. b. The Ringer Equivalence Number (REN). c. The USOC jack required. d. The FCC Registration number. Items (b) and (d) are indicated on the label. The Ringer Equivalence Number (REN) is used to determine how many devices can be connected to your telephone line. In most areas, the sum of the REN's of all the devices on any one line should not exceed 5.0. If too many devices are attached, they may not ring properly. FCC Part 15 Registration This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interface, and 2. This device must accept any interface received including interface that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning off and on, the user is encouraged to try to correct the interference by one or more of the following measures: .. Reorient or relocate the receiving antenna. .. Increase the distance between the equipment and receiver .. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. .. Consult an experienced radio/TV technician for help. CTR 21 pan-European Certification This equipment has been approved in accordance with Council Decision 98/482/EC for pan-European single terminal connection to the public switched telephone network (PSTN). However, due to differences between the individual PSTNs provided in different countries, the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point. In the event of problems, you should contact your equipment supplier in the first instance. This device is designed to work with the notified networks in all EC member states. Nevertheless, some of the network services in invidual countries might not be supported, but they will not affect the normal data and fax applications. For example, the metering charge service in Germany. Besides you may encounter difficulty of using PULSE dialing function in some of the countries, such as Nordic countries. This kind of network compatibility is dependent on the physical and software settings of this device. If the users are desired to use this device on those networks, they should contact the vendor or supplier first. HARDWARE INSTALLATION Precautions: Please be sure you take adequate anti-static precautions when handling this product. The simplest way to achieve this is; touch a non-painted surface of the computer’s chassis during the hardware installation. 1. Make sure the computer is turned off before installing the device. 2. Remove the expansion slot cover from the computer. 3. Carefully slide the PCI modem card into an available PCI slot, applying even pressure to the card. Secure the card to the computer with the screw. (PCI slots are 85mm long and positioned 40mm from the PC’s rear panel. Generally there are several PCI slots side by side). 4. Plug one end of the telephone cable into the Modem line jack and another end into the telephone jack in wall. 5. Replace the cover. 6. You are now ready to continue the software installation. SOFTWARE INSTALLATION Windows 98 Installation 1. Reboot the computer system after the modem is well inserted into the PCI slot of your computer. Windows 98 will automatically detect the device. Click Next to continue. 2. Insert the device driver compact disc into your CD-ROM drive when the following dialog box appears. Click Next to continue. 3. Select Specify a location and press Browse to choose the Dirver\Win98 folder in your CD-ROM drive. T...