Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Setup is as easy as can be -simply connect the computer system box and local console to the Local KVM EXTENDER USB Module; run the Category 5 cable to the Remote KVM EXTENDER USB Module (up to 150 meters away); and plug the remote console into the Remote Module. Note: You can control numerous remote systems from a single console by combining the KVM EXTENDER USB with a USB KVM switch like LINDY Part No. 32824 or 32341. System Requirements for Consoles • VGA, SVGA, or Multisync monitor capable of the highest resolution that you will be using on any computer in the installation • USB Keyboard and USB Mouse Note: 1. If you connect a DDC type monitor to the Local unit, the monitor that connects to the Remote unit must be able to support the highest video resolution that the DDC monitor can provide. 2. You must use the same brand and model of mouse on both the local and remote units. System Requirements for Computers The following equipment must be installed on each computer that is to be connected to the system: • AVGA, SVGAor Multisync card • USB Host Controller and Type A USB Port System Requirements for Cables For optimum signal integrity and to simplify the layout, we strongly recommend that you use the high quality USB and VGA cables. Category 5 cable is the minimum required to connect the local and remote KVM EXTENDER USB units. Using cable of a lesser standard will result in degrading the video signal. For the utmost performance, we strongly recommend Category 5 STP or FTP cable. The Local Unit Pressing the Operating Mode Selection Switch button toggles between the operating mode choices: 1. Local -only the local console can control the system(s) 2. Auto -both consoles can control the system(s). LEDs The Local Unit has two LEDs to indicate the operating status of the Local and Remote units (see table for details). Front Side Connectors: USB Keyboard and Mouse Ports, Monitor Port The local USB Keyboard and local USB mouse plug into these connectors (USB Type A sockets). The local monitor plugs into this connector (HD-15 socket). Right Side Connector: Remote I/O The Category 5 cable (RJ-45 connector) that connects to the Remote Unit plugs into this socket. Connectors on the back: USB B Port and Monitor Port The USB B Connector of the USB cable to the local computer (or USB KVM Switch) plugs in here. The HD-15 female Connector of the VGA cable to the graphics card (or KVM Switch) plugs in here. Note: If you are combining the KVM EXTENDER USB with a KVM switch like LINDY Part No. 32823 or 32341, the extension cable connects back to the respective ports on the Console section of the switch. © LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH -FIRST EDITION (June 2002) USER MANUAL TheRemoteUnit LEDs The Remote Unit has two LEDs (Status and On Line) to indicate the status of the Local and Remote units. USB Keyboard and Mouse Port, Monitor Port The remote USB keyboard and USB mouse plug into these connectors. The remote monitor plugs into this connector. Right Side Connector: Remote I/O The Category 5 cable (RJ-45 connector) that connects back to the Local Unit plugs into this socket. Installation of the KVM Extender USB Units Setting up the KVM Extender System is simply a matter of plugging in the cables: 1. Make sure that all the equipment to be connected up is powered off. 2. Plug the cables from the local console devices (mouse, keyboard, monitor), into their ports on the Console side of the Local Unit (KVM EXTENDER USB). 3. Plug the appropriate connectors on the USB and VGA cables into the CPU side of the KVM EXTENDER USB. Note: A monitor extension cable male/female has to be used. 4. Plug the connectors on the other end of this cables into the appropriate ports on the computer system (or USB KVM switch). 5. Plug either end of the Category 5 cable into the KVM EXTENDER USB Local Unit’s Remote I/O port. 6. Connect one of the power adapters (supplied with this package) to the Local Unit. 7. Plug the other end of the Category 5 cable into the I/O port of the Remote Unit (KVM EXTENDER USB). 8. Plug the cables from the remote console devices (USB mouse, USB keyboard, monitor), into their ports. 9. Connect the second power adapter (supplied with this package). Operation The Local and Remote Units each have two LEDs to indicate their operating status, as shown in the tables, below: Local Unit Remote Unit Operating Mode LEDs LOCAL REMOTE Local Console ACTIVE Flash OFF Remote Console Active OFF Flash Error / Disconnect ON OFF Not Ready OFF OFF Neither Console Active ON ON Operating Mode LEDs STATUS ONLINE Local Console ACTIVE OFF OFF Remote Console Active Flash Flash Error / Disconnect OFF Flash Not Ready OFF OFF Neither Console Active ON ON Troubleshooting If no video picture is shown make sure that all cables are securely plugged into their sockets. If you still see no video picture then try connecting with a short Cat.5 patch cable to make sure it is not due to a faulty Cat.5 STP or FTP cable. © LINDY ELECTRONICS...