Votos - 3, Puntuación media: 3.3 ( )

Fabricar: Humminbird Tamaño del archivo: 383.84 kb Nombre del archivo: 963fceab-6840-4681-b1d0-5f5ca42e9b9e.pdf Idioma del manual:

1. Assembling (Fig. 1) (1) Turn the grinder upsidedown so that the spindle is facing upward. (2) Mount the wheel washer onto the spindle. (3) Fit the protuberance of the depressed center wheel or diamond wheel onto the wheel washer. (4) Assemble the wheel nut onto the spindle. (For diamond wheel assembling, use the wheel nut with the convex side against the diamond wheel.) (5) Insert the push button to prevent rotation of the spindle, and tighten the wheel nut with accessory wrench, as shown in Fig. 1. 2. Disassembling Follow the above procedures in reverse. CAUTIONS: . Confirm that the grinder wheel is mounted firmly. . Confirm that the spindle lock mechanism is disengaged by pushing push button two or three times before switching the grinder on. MAINTENANCE AND INSPECTION 1. Inspecting the depressed center wheel Ensure that the depressed center wheel is free of 2. Inspecting the mounting screws Regularly inspect all mounting screws and ensure that they are properly tightened. Should any of the screws be loosened, retighten them immediately. Failure to do so could result in serious hazard. 3. Inspecting the carbon brushes (Fig. 5) The Motor employs carbon brushes which are consumable parts. When they become worn to or near the “wear limit”, it could result in motor trouble. When an auto-shop carbon brush is equipped, the motor will stop automatically. At that time, replace both carbon brushes with new ones which have the same carbon brush Numbers shown in the figure. In addition, always keep carbon brushes clean and ensure that they slide freely within the brush holders. 4. Replacing a carbon brush (Fig. 6) (1) Loosen the D4 tapping screw retaining the tail cover and remove the tail cover. (2) Use the auxiliary hexagonal wrench or small screwdriver to pull up the edge of the spring that is holding down the carbon brush. Remove the edge of the spring toward the outside of the brush holder. (3) Remove the end of the pig-tail of the carbon brush from the terminal section of brush holder and then remove the carbon brush from the brush holder. (1) Insert the end of the pig-tail of the carbon brush in the terminal section of brush holder. (2) Insert the carbon brush in the brush holder. (3) Use the auxiliary hexagonal wrench or small screwdriver to return the edge of the spring to the head of the carbon brush. (4) Mount the tail cover and tighten the D4 tapping screw. 5. Maintenance of the motor The motor unit winding is the very “heart” of the power tool. Exercise due care to ensure the winding does not become damaged and/or wet with oil or water. NOTE: Due to HITACHI’s continuing program of research and development, the specifications herein are subject to change without prior notice. Information concerning airborne noise and vibration The measured values were determined according to EN50144. The typical A-weighted sound pressure level: 85 dB (A). Wear ear protection. The typical weighted root mean square acceleration value does not exceed 2.5m/s2. cracks and surface defects. 19 G13SE G13SE Item Part Name No.1 Seal Lock Screw (W/Sp. Washer) M4 10 2 Tapping Screw D5 25 3 Pushing Button 4 Gear Cover Ass'y 5 Special Nut M7 6 Pinion 7 Seal Ring (A) 8 Washer (C) 9 Ball Bearing (629T12DDC3PS2-L) 10 Rubber Ring 11 Felt 12 Bearing Cover 13 Armature 14 Fan Guide 15 Hex. Hd. Tapping Screw D4 70 16 Stator 17 Thrust Washer 18 Dust Seal (A) 19 Ball Bearing (608VVMC2EPS2L) 20 Lock Pin 21 Gear 22 Seal Lock Screw (W / Sp. Washer) M4 8 23 Bearing Cover (B) 24 Ball Bearing (6201DDUCMAV2S) 25 Felt Packing 26 Seal Packing 27 Packing Gland 28 Seal Lock Screw (W / Sp. Washer) M5 16 29 Feather Key 3 3 8 30 Spindle (A) 31 Label 32 Set Pin 33 Lever 34 Machine Screw (W / Washer) M5 25 35 Set Piece (B) 36 Retaining Ring (E-Type) For D2.5 Shaft 37 Wheel Guard Ass'y 38 Wheel Washer 39 Wheels 125MM A36Q D.C. 40 Wheel Nut M14 41 Gear Ass'y 42 HITACHI Label 43 Housing 44 Name Plate ItemNo. Part Name45 Rubber Ring46 Switch Box 47 Noise Suppressor48 Terminal 49 Tail Cover (B) 50 Tapping Screw (W / Flange) D4 35 51 Connector (50091) 52 Piller Terminal53 Tapping Screw (W / Flang) D4 20 54 Carbon Brush55 Brush Holder56 Tapping Screw D3 10 57 Spring 58 Tail Cover (A) 59 Switch 60 Tapping Screw (W / Flange) D4 16 61 Terminal 62 Cord Clip 63 Cord Armor64 Cord 65 Spring 66 Paddle Lever67 Lever Action Seal68 Spring (F) 69 Feather Key 3 3 15 70 Lock Lever 501 Wrench 502 Side Handle Parts are subject to possible modification withoutnotice due to improvements.The drawing and the list are parts structural drawingand parts list of model G13SE. For model G12SErefer to the drawing and the list. Svenska Suomi EF-DEKLARATION BETRAFFANDE LIKFORMIGHET EY-ILMOITUS YHDENMUKAISUUDESTA Vi tillkannagiver med eget ansvar att denna produkt Yksinomaisella vastuudella vakuutamme, etta tama overensstammer med standard eller standardiserat tuote vastaa normeja tai normitettuja dokumentteja dokument EN50144, EN55014 och EN61000-3 i enl...

Descargar ahora

Introduzca dos números de la imagen: