Votos - 5, Puntuación media: 4.2
(
)
)
|
Resumen del manual
This will help prevent excessive metal accumulation on the grinding wheel. Angle Guide The Model T10010 Wet Grinder comes with an angle guide to help identify and maintain the cutting angle on a variety of tools. Figure 11. Measuring notches. Angle Edge Desired Angle Notch Measuring Notches Workpiece 2. Find the angle notch that best fits the tool you wish to grind by placing the sharpened edge of the workpiece into each notch. 3. Place the angle guide on the wheel with the desired angle notch (found in Step 2) against the wheel and adjacent to the universal support (Figure 12). Figure 12. Angle guide usage. Desired Angle Notch Correct Grinding Angle Angle Edge Workpiece 4. Adjust the positioning of the tool and the universal support height as necessary so that the sharpened edge of the tool is flat against both the grinding wheel and the angle edge on the angle guide as shown in Figure 12. For precision grinding attachments, see Accessories on Page 17. Model T10010 Wet Grinder -15 Wheel Dressing Sharpening Depending on the type of grinding you do, the grinding wheel may require periodic dressing. A variety of dressing tools are available (see Accessories, Page 17) and can be used to restore the abrasive quality of the wheel surface and bring the wheel edge back to a square form. Refer to the instructions that accompany your dressing accessory for complete details on how to properly dress a wheel. The leather stropping wheel on the Model T10010 and the included abrasive stropping paste can be used to obtain a razor sharp edge on many tools. Before use, the stropping wheel must be properly prepared. To prepare the stropping wheel: 1. DISCONNECT GRINDER FROM POWER. 2. Make sure the wet grinder is disconnected from power and that the stropping wheel is not rotating. 3. Evenly apply a light machine oil to the leather wheel. Use enough oil to provide a thorough coating, but not so much as to saturate the leather and result in dripping. 4 Apply a thin coat of abrasive honing paste to the leather wheel using a wooden spreader or similar device. Distribute the paste evenly by hand- turning the wheel while spreading. 5. Turn the machine on and continue to distribute the paste, still using the wooden spreader. Move the spreader lightly in a circular motion across the wheel. 6. Once the paste is evenly distributed, begin sharpening. These preparations will be sufficient for sharpening five to ten tools. If you notice a drop in sharpening performance or have sharpened more than ten tools, repeat Steps 1-6. -16- Model T10010 Wet Grinder SECTION 5: ACCESSORIES T10023—Accessory Kit #1 Includes fixtures T10025—Sharpening Jig. Jig for sharpen- for sharpening small knives, large knives, scis-ing 16" planer blades sharpens all planer and sors and axes. jointer blades up to 16" long. Figure 14. Model T10023 T10024—Accessory Kit #2 Includes a stone dresser and fixtures for sharpening scrapers, screwdrivers and hollow chisels. Figure 15. Model T10024. Figure 16. Model T10025. G7120—Heavy Duty Grinder Stand This is one of the most stable bench grinder stands on the market. Once you have one, you’ll wonder how you ever got along without it. 321.2" high. Will require the installation of a tabletop (not included) for use with the Model T10010 Wet Grinder. 49 lbs. Figure 17. Model G7120. Model T10010 Wet Grinder -17 H5891, H5892 Diamond Dressers Industrial diamond for dressing grinding wheels. 8." long round body with knurled grip for maximum control. Includes protective rubber end cap. Model H5891 . Carat. Model H5892 . Carat. Figure 18. Models H5891 & 5892. H5944, H5945, H5946 Wheel Dressers Exposes new grains for aggressive cutting on all types of grinding wheels. Star wheels and discs are hardened steel. Cast iron handle provides stabilizing mass for better control. H5944 #0 Wheel Dresser. H5945 #1 Wheel Dresser. H5946 #2 Wheel Dresser. Figure 19. Models H5944, H5945, H5946. -18-Model T10010 Wet Grinder SECTION 6: MAINTENANCE ! Always DISCONNECT POWER before servicing, adjusting, or doing main- tenance to reduce the risk of acci- dental injury or electrocution. For optimum performance from your machine, routinely check the condition of the following items and repair or replace as necessary: • Cracked or loose grinding wheel. • Loose hardware. • Bent universal support. • Worn switch. • Worn or damaged cords and plugs. • Any other condition that could hamper the safe operation of this machine. Grinding Wheels The grinding wheel should be inspected before every use. Use the ring test method noted in Wheel Inspection on Page 10 to verify the structural integrity. Take care in storing grinding wheels to keep them free from potential damage from moisture, by being dropped, or having other items drop on them. Wheel Replacement To replace the grinding or stropping wheel: 1. DISCONNECT THE GRINDER FROM POWER! 2. Hold the wheel from turning, and remove the arbor nut or knob which holds the wheel on. 3. Remove the outer washer and wheel. 4....