Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Sharp edges on metal parts may cause personal injury. Examine the edges of all metal parts before handling. Cabinet Assembly The Model G0529 Sander mounts on a sturdy cabinet stand. To assemble the cabinet stand: 1. Connect all four panels together with the 5.16" -18 x 3/4" hex bolts, lock washers, washers and hex nuts (Figure 3). Figure 3. Assembled panels. 2. Using the 5.16" flat head screws, 5.16" washers and nuts, install the four rubber feet as shown in Figure 4. Figure 4. Installing rubber feet. -12- G0529 Oscillating Spindle & Disc Sander Mounting Sander Installing Spindle When the cabinet has been completed, it is time to place the sander unit on top of the cabinet stand. To mount the sander to the top of the cabinet stand: 1. With the help of an assistant, place the sander on the cabinet stand. The Model G0529 weighs 143 lbs. Personal injury could occur if the machine is moved without additional assistance. Seek help when moving or lifting the machine. 2. Align the holes on the rim of the cabinet sides with the threaded holes in the rim of the sander. 3. Secure the cabinet and the sander together with the 5.16"-18 x 11.4" hex bolts, 5.16" lock washers, and 5.16" flat washers combination as shown in Figure 5. ! To install the spindle onto the sander: 1. Disconnect the machine from the power supply. 2. Select the proper diameter of spindle sleeve. The Model G5029 comes with the following four sizes of spindle sleeves: • 1.4" • 5.8" • 1 1.2" •2" 3. Make sure the tapered end of the spindle sleeve is clean before installing it into the sander spindle. 4. Use the supplied open end wrenches to secure the spindle as shown in Figure 6. Note—Do not over tighten the spindle sleeve, it could make removal difficult. ! Figure 6. Installing spindle. Figure 5. Cabinet hole location. G0529 Oscillating Spindle & Disc Sander -13 Table Inserts Squaring Table The table inserts minimize the gap between the working surface edge and the spindle. It is important to use the proper table insert according to the diameter spindle you are using. The Model G5029 comes with the following four table inserts: • 2" • 1" • 2" elliptical • 1" elliptical Select the table insert that comes closest the spindle sleeve diameter without touching it. The elliptical inserts are used when sanding with the table tilted. Place the table insert into the table hole as shown in Figure 7. ! Figure 7. Installing table inserts. To square the sanding tables: 1. Disconnect the machine from the power supply. 2. Set the table at 90° as shown in Figure 8. ! Pointer Figure 8. Setting the table scale at 90°. 3. Place a machinist square on the table and against the sanding spindle to verify the table is 90° from the edge of the sanding sleeve as shown in Figure 9. 4. Adjust the pointer to 90°. ! Figure 9. Squaring the table and spindle. -14- G0529 Oscillating Spindle & Disc Sander 5. If the table is not 90° from the spindle, adjust the table stop bolt to allow the table to move more as shown in Figure 10. ! Figure 10. Squaring the sanding table. 6.Tighten the table stop bolt against the under- side of the table when the table is set at 90°. Squaring Disc Sander The sanding tables for the spindle sander and the disc sander have tilting capabilities from 0° to 45°. To tilt the sanding table: 1. Disconnect the machine from the power supply. 2. Using a machinist square, set one edge on the table surface and the other against the face of the sanding disc as shown in Figure 11. Note—This can be done with the sandpaper installed, although it is somewhat easier to measure if the disc does not have the sandpaper disc installed. Figure 11. Squaring the sanding table. 3. Loosen the lock lever and adjust the table angle until it is perfectly perpendicular and flush with both edges of the machinist square. 4. Tighten the lock lever while holding the table perpendicular. 5. Adjust the scale pointer to read 0° when the table has been properly adjusted. G0529 Oscillating Spindle & Disc Sander -15 Sanding Disc Installation The disc sander requires 12" sanding discs with hook and loop backing. To install a new sanding disc on the 12" disc sanding surface: 1. Disconnect the machine from the power supply. 2. Remove the disc sanding table. 3. Remove the old sanding disc. 4. Install the new sanding disc as shown in Figure 12. ! Figure 12. Installing sanding disc. Aligning Table The table must be aligned to the face of the sanding disc so that the sandpaper does not rub against the table. To align the table: 1. Loosen the bolts that secure the table to the table support bracket as shown in Figure 13. ! Figure 13. Loosening table bolts. 2. Align the table so that there is a 1.16'' gap between the 12" disc and the table. 3. Tighten the bolts loosened in step 1. 4. Spin the disc by hand to check if the sandpaper is touching the table. Note—DO NOT turn the disc sander on at this point. 5. Repeat steps 1-3 if the sandpaper touches table at any point in the rotation. -16- G0529 Oscillati...