Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
In addition to maintaining safe control during use, the side handle also provides convenient ease of operation for the operator. Spindle Lock Button The spindle lock button secures the spindle so that only one wrench is needed to change the grinding wheel. Switch with Lock-on Feature Your grinder has a conveniently located switch. It also has a lock-on feature that allows the grinder to be locked in the on position when continuous operation for extended periods of time is required. APPLICATIONS (Use only for the purposes listed below) ¦ Grinding metals. ¦ Sanding wood or metal surfaces. ¦ Wire brushing rusted or painted surfaces. WARNING: Do not allow familiarity with your grinder to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. Fig. 1 SPINDLE LOCK BUTTON TRIGGER SWITCH SIDE HANDLE GUARDGRINDING WHEEL LOCK-ON BUTTON ASSEMBLY WARNING: Your grinder should never be connected to power supply when you are assembling parts, making adjustments, installing or removing grinding wheels, or when not in use. Disconnecting your grinder will prevent accidental starting that could cause serious injury. INSTALLING THE SIDE HANDLE See Figure 2. ¦ Unplug your grinder. Fig. 2 GEAR HOUSING SIDE HANDLE Page 8 Page 9 ASSEMBLY CLAMP NUT GRINDING WHEEL DISC FLANGE SPINDLE SPINDLE LOCK BUTTON FLAT(S) WRENCH TO TIGHTEN TO LOOSEN ¦ Place the accessory wheel over the spindle. WARNING: Always install grinding wheel and abrasive mop disc with the depressed center against the disc flange as shown above. Failure to do so will cause the grinding wheel to crack when tightening the clamp nut. This could result in serious personal injury because of loose particles breaking off and being thrown from the grinder. Do not overtighten. ¦ To install grinding wheel and wire wheel brush: Thread the clamp nut on the spindle with the flat side of nut facing up. Fit raised, small diameter portion of the clamp nut into the hole in the wheel and finger tighten. See figures 3A and 3B. ¦ To install abrasive mop disc: Thread the clamp nut on the spindle with the flat side of nut facing down. Finger tighten. See figure 3C. ¦ Depress the spindle lock button and rotate the wheel clockwise until the spindle locks in position. ¦ Securely tighten the clamp nut with the wrench provided. Do not overtighten. WARNING: Wire wheel brush bristles will bend during use and show their direction of rotation. When reusing the wire wheel brush, always mount it to rotate in the same direction as in prior use. Failure to heed this warning can result in bristle breaking and extreme vibration of the wire wheel brush that could result in serious personal injury. WARNING: Failure to unplug your grinder could result in accidental starting causing serious injury. ¦ Install the side handle by screwing it into the side of the gear housing. Note: The handle can be installed on either the left or right side of the grinder, depending on operator preference. It must always be used to prevent loss of control and possible serious injury. ¦ Tighten side handle securely. INSTALLING ACCESSORY WHEELS See Figures 3A, 3B, and 3C. ¦ Unplug your grinder. WARNING: Failure to unplug your grinder could result in accidental starting causing serious injury. ¦ Your grinder is shipped with the disc flange and clamp nut attached to the spindle. ¦ Depress spindle lock button and rotate clamp nut until spindle locks. To prevent damage to the spindle or spindle lock, always allow motor to come to a complete stop before engaging spindle lock. ¦ Loosen and remove clamp nut from spindle. Do not remove disc flange. ¦ Make sure flats on the bottom of disc flange are engaged with flats on spindle. Fig. 3A CLAMP NUT TURNED CORRECT CLAMP NUT TURNED INCORRECT TO TIGHTEN TO LOOSEN WIRE WHEEL BRUSH Fig. 3B CLAMP NUT TURNED INCORRECT DISC FLANGE CLAMP NUT TO TURNED CORRECT TIGHTEN TO LOOSEN ABRASIVE MOP DISC DISC FLANGE Fig. 3C ADJUSTMENTS ADJUSTMENTS Fig. 4 INCORRECT LOCATION OF GUARD CORRECT LOCATION OF GUARD IS BETWEEN POINTS A AND B WARNING: Do not attempt to operate this tool until you have read thoroughly and understand completely all instructions, safety rules, etc. contained in this manual. Failure to comply can result in accidents involving fire, electric shock, or serious personal injury. Save operator's manual and review frequently for continuing safe operation, and instructing others who may use this tool. Fig. 5 Fig. 6 A B WARNING: Before connecting your grinder to power supply, always check to be sure switch is not in lock-on position. Failure to do so could result in accidental starting of your grinder resulting in possible serious injury. GUARD LOCATION The guard on your grinder should be correctly installed depending on which side the handle is mounted. Never use your grinder without the guard correctly in place. Figures 4-6 show correct and incorrect locations of the guard. WARNING: Never place the guard so that it is on front of the grinder as sh...