Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
The bearings within are sealed and do not require lubrication. Mounting Sanding Disc Remove Table (59) surrounding Sanding Disc (23). Peel off old Sanding Disc. Align perimeter of new Sanding Disc (23) over Aluminum Disc (22). When aligned, press disc firmly onto Disc. Most Sanding Discs have self-adhering properties. Others may require application of an appropriate glue (not supplied). Replace Table (59). Sanding Belt Replacement Push the Belt Tension Lever (34) to the right to loosen the Belt (4). Slide the old Sanding Belt (4) off the Idler Roller (41) and Drive Drum (5). Slide the new Sanding Belt (4) onto the Idler Roller (41) and Drive Drum (5). Refer to the Parts List for correct Belt (4) replacement size. Push the Belt Tension Lever (34) to the left to tighten the Belt (4). Turn on the Belt Sander to test the new Belt. If the Belt tracks to one side, go to page 11 and follow the procedure for Belt Tracking Adjustment. Troubleshooting SYMPTOM PROBABLE CAUSE REMEDY Belt Sander does not turn on Not plugged in to electrical outlet Switch key not inserted into Switch GFCI or facility circuit breaker open Power Switch defective Motor or wiring problem Connect to outlet Insert Switch Key, then push Switch to On position Reset circuit breakers Replace Switch Repair with a qualified technician Motor slows when sanding V-Belt too tight Sanding with too much pressure on stock A qualified technician needs to loosen tension Apply less pressure when sanding Sanding Belt runs off Idler Roller Not tracking properly Adjust Sanding Belt Tracking Wood burns while sanding Sanding Disc or Belt is loaded with debris Clean or replace Disc or Belt. Sander makes excessive noise V-Belt too tight A qualified technician needs to loosen Parts List PartDescriptionQty. 1Bolt, Pan Head, 4x8mm61AWasher, Lock, 4mm61BWasher, Flat, 4mm62Bearing Plate ll13Ball Bearing, 620124Belt, Sanding, 4”x36”15Drive, Drum16Drive Shaft17Block Stop18Platen19Screw with Set Square210Bearing Plate l111Plate, Reinforcing112Table Bracket113Nut, Hex, 8mm814Horizontal Stop115Strain Relief216Switch116ABolt, Pan Head, 5x12mm316BWasher, Lock, 5mm116CWasher, Serrated, 5mm117Set Screw, 6x6mm318V-Belt119Pulley, Drive120Bolt, Hex, 8x12mm221Washer, Flat, 8mm422Disc, Aluminum123Disc, Sanding124Bolt, Hex, 6x12mm225Washer, Flat, 6mm226Bolt, Pan Head, 5x15mm127Washer, Flat, 5mm128Pulley Cover129Pulley Cover Plate130Washer, Flat, 5mm131Washer, Lock, 5mm132Nut, Hex, 5mm133Motor134Tension Lever1PartDescriptionQty. 35Adjusting Knob136Adjusting Spring137Block Plate138Push Back Spring139Idler Roller Shaft140Ball Bearing, 6201241Idler Roller141AScrew, Round Head142Bolt, Hex, 8x16mm843Washer, Flat, 8mm1244Base145Feet445AMotor Pulley146Nut, Hex, 10mm147Rod148Pivot Bracket149Table Bar150Set Screw, 8x8mm251Bolt, Hex, 8x10mm252Washer, Lock, 8mm253Washer, Flat, 8mm254Washer, Flat, 8mm155Adjusting Knob156Table Tilt Trunion157Bolt, Pan Head, 5x10mm158Pointer159Table160Finger l161Washer, Lock, 4mm161AWasher, Flat, 4mm162Bolt, Pan Head, 4x5mm163Screw, Lock164Miter Gage165Miter Bar166Line Cord167Washer, Lock, 4mm468Washer, Flat, 4mm469Nut, Hex, 4mm470Wrench1NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. PLEASE READ THE FOLLOWING CAREFULLY The manufacturer and/or distributor has provided the parts list and assembly diagram in this manual as a reference tool only. Neither the manufacturer or distributor makes any representation or warranty of any kind to the buyer that he or she is qualified to make any repairs to the product, or that he or she is qualified to replace any parts of the product. In fact, the manufacturer and/or distributor expressly states that all repairs and parts replacements should be undertaken by certified and licensed technicians, and not by the buyer. The buyer assumes all risk and liability arising out of his or her repairs to the original product or replacement parts thereto, or arising out of his or her installation of replacement parts thereto. Assembly Drawing Record Product’s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Warranty card Limited 90 day/1 Year warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser for a period of ninety days from date of purchase that the motor, the belts (if so equipped), and the blades (if so equipped) are free of defects in materials and workmanship. Harbor Freight Tools also warrants to the original purchaser, for a period of one year from date of purchase, that all other parts and components of the product are free from defects in materials and workmanship. This warranty does not apply to damage due directly or indirectly to misuse, abuse, negligence or accident...