Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
9. Make sure there are no foreign objects, such as nails, in your workpiece. 10. Don’t use dull or damaged bits. Dull or damaged bits may break off and cause serious injury. Replacement accessories are available at Harbor Freight Tools. 11. After changing bits or accessories, make sure the collet is securely fastened. 12. Any accessory used with this tool must be rated at 16,250 RPM or greater. Unpacking When unpacking, check to make sure the parts listed on page 6 and 8 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Operation Note: Always disconnect the tool from the power adapter while loading, unloading, or adjusting accessories. 1. Choose the appropriate Collet (7) for the shank of the accessory you are using. 2. Just above the collet shaft on the end of the tool, there is a shaft lock button. Depress that button to lock the shaft so that you can open the Collet (7). 3. Remove the Collet Nut (6) on the tip of the tool and add the appropriate Collet (7). Put the bit or accessory you want in the Collet (7). Continue to depress the shaft lock button while tightening the Collet Nut (6). 4. Make certain that the power switch is in the off (O) position. Plug the Adapter (13) into a properly grounded, 120 VAC outlet. Connect the plug from the Rotary Tool (1) to the connector on the end of the adapter’s cord. 5. Hold the tool firmly in one hand. Turn the toggle switch on ( I ) and wait until the tool reaches full speed before contacting the workpiece. 6. When finished, turn off (O) the toggle switch and unplug the unit. Operational Tips. 1. When you turn on the tool, hold it a safe distance in a direction away from your face. 2. Practice on scrap material while getting use to the feel of the tool. 3. Never lean on the tool. Allow the speed of the tool to do the work for you. Lightly contact the material. It is better to make several passes on a workpiece than to try to remove a lot of material in one pass. A gentle touch works best. If you feel the job is not getting done, change to a more powerful cutter. 4. Plastics and similar materials will melt when contacted with high speed accessories. Start very slowly and monitor the material carefully. 5. Follow all warnings and safety precautions and operational warnings as outlined in this manual completely. Accessory Tips. (Some of the many uses.) 1. Mandrels are the shanks with a threaded or screw head. They are required when you use the cutoff wheels, polishing wheels, and sanding discs. The mandrel without the nut on the end is for the felt polishing wheels. For cutoff wheels and sanding discs, remove the nut on the end of the mandrel, add the wheel or disc, and replace the nut. 2. Cutters are used for cutting, carving and slotting materials. 3. Grinding Stones are used for sharpening cutting tools, screwdrivers etc. They can also be used to deburr any metal after the cutting process. Also, they can be used to remove excess glaze on ceramics. 4. Cutting Wheels are used for slicing or cutting off bolt heads, nuts, etc. 5. Wire Brushes clean silverware, jewelry, and antiques. SKU 94076 For technical questions, please call 1-800-444-3353. Page 4 6. Sanding accessories can be used on a variety of workpieces, ranging from models to fine furniture. 7. Polishing accessories bring metal surfaces to a smooth finish. Parts List Part Description Qty. Maintenance Note: Always disconnect the power adapter from the electrical outlet before attempting any maintenance. 1. While wearing safety goggles and a full face shield, use compressed air to clean out the tool’s vents. 2. Clean the collet shaft of any dirt or debris. 3. Wipe the tool down with a soft cloth. Do not use any solvents to clean the tool as they will permanently damage the tool. 4. If the Rotary Tool begins to work less efficiently, or slow down, have the internal brushes replaced by an qualified technician. PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. SKU 94076 For technical questions, please call 1-800-444-3353. Page 5 Assembly Diagram SKU 94076 For technical questions, please call 1-800...