Votos - , Puntuación media: ( )

Manual de usuario Makita, modelo 9563CV

Fabricar: Makita
Tamaño del archivo: 769.91 kb
Nombre del archivo:

Idioma del manual:

El documento se está cargando, por favor, espere

Descargar ahoraCerca

El documento se está cargando, por favor, espere

Descargar ahoraCerca

Service or maintenance performed by unqualified personnel could result in a risk of injury. 24.,When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury. USBOOS-l Specific Safety Rules 1. Always use proper guard with grinding wheel. A guard protects operator from broken wheel fragments. 2. Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other accessories running over rated speed can fly apart and cause injury. 3.Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. 4. Keep guards in place. 5. Use only wheels having a maximum operating speed at least as high as "No Load RPM" marked on the tool's nameplate. When using depressed center wheels, be sure to use only fiberglass-reinforced wheels. 6.Check the wheel carefully for cracks or damage before operation. Replace cracked or damaged wheel immediately. 7. Use only flanges specified for this tool. 8. Be careful not to damage the spindle, the flange (especially the installing surface) or the lock nut. Damage to these parts could result in wheel breakage. 9. Hold the tool firmly. IO.Keep hands away from rotating parts. 11. Make sure the wheel is not contacting the workpiece before the switch is turned on. 12.Before using the tool on an actual workpiece, let it run for a while. Watch for vibration or wobbling that could indicate poor installation or a poorly balanced wheel. 13.Use the specified surface of the wheel to perform the grinding. 14. Watch out for flying sparks. Hold the tool so that sparks fly away from you and other persons or flammable materials. 15. Do not leave the tool running. Operate the tool only when hand-held. 16.Do not touch the workpiece immediately after operation; it may be extremely hot and could burn your skin. SAVE THESE INSTRUCTIONS. SYMBOLS The followings show the symbols used for tool. v .................................... volts A .................................... amperes Hz .................................... herts .................................... alternating current b .................................... no load speed H.................................... Class II Construction .../min ................................... revolutions or reciprocation per minute ?., FUNCTIONAL DESCRIPTION Switch action CAUTION: Before plugging in the tool, always check to see that the switch actuates properly and returns to the "OFF" position when the side of the switch lever is depressed. To start the tool, slide the switch lever to "I" position. Switch lever For continuous operation, depress the front of the switch lever and then slide to "I" position as above. The switch is locked on the position for continuous operation. To stop the tool from the locked position, slide the switch lever to "0"position with depressing its rear part. Depressing the rear of the switch lever. Speed adjusting dial The rotating speed can be changed by turning the speed adjusting dial to a given number setting from 1 to 5. Higher speed is obtained when the dial is turned in the direction of number 5. And lower speed is obtained when it is turned in the direction of number 1. Refer to the table below for the relationship between the number settings on the dial and the approximate rotating speed. II Number RPM (mid 2800 1 4000 1 6500 1 9000 1 10500 k3peed adjusting dial CAUTION: The speed adjusting dial can be turned only as far as 5 and back to 1. Do not force it past 5 or 1, or the speed adjusting function may no longer work. ASSEMBLY Installing and removing wheel cover Installing Pull the lever in the direction of the arrow after loosening the screw. Install the wheel cover on the bearing box by adjusting the convex of the wheel cover to the concave of the bearing box. Turn the wheel cover by 180 degrees. Fasten it with the screw after pulling the lever the direction of the arrow. For the working purpose, the setting angle of the wheel cover can be adjusted with the lever Removing wheel cover Follow the installation procedure in reverse to remove the wheel cover Installing side grip (auxiliary handle) Screw the side grip on the tool securely. The side grip can be installed on either side of the tool, whichever is convenient. Shaft lock Press the shaft lock to prevent spindle rota- tion when installing or removing acces- Shaft lock sories. CAUTION: Never actuate the shaft lock when the spindle is moving. The tool may be dam- aged. Installing or removing the depressed center wheel CAUTION: Always be sure that the tool is switched off and unplugged before installing or removing the wheel. Mount the inner flange onto the spindle. Fit the wheel on over the...