Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
WARNING: Do not cut, remove or break theground pin. If the outlet does not fit the plug, consult your electrical contractor. WARNING: Have worn, cut or damagedcords replaced by an authorized service person. EXTENSION CORDS Use only an approved extension cord with three conductors, a plug with three terminals, and a connector body with three holes. The machine has a power cord with wire size 14 AWG (AWG means American Wire Gauge). WARNING: If you use an extension cord, use an extension cord with minimum wire size 12 AWG. Do not use an extension cord longer than 50 feet. Do not join two extension cords. Grounded Outlet Box Grounded Outlet Grounding Pin (United States, Mexico and Canada) Figure 3 Clarke® American Sanders Operator's Manual (EN) -RS-16 /RS-16DC - 7 ENENGLISH HOW TO OPERATE THE MACHINE ENENGLISH HOW TO OPERATE THE MACHINE OPERATION (Figure 4) 1 Unwrap the Power Cord (5) and plug it into a properly grounded outlet. 2 Pull up on the Handle Release Compression Lever (4). Move the Operator Handle (6) downward until your arms are almost straight. Push down on the Handle Release Compression Lever (4) to lock it in place. 3 Lift up on the Operator Handle (6) until the brush (or pad) is flat against the floor. WARNING! Be prepared to control the machine as soon as the motor starts. Just a slight up or down movement of the Handle will make the machine move from side to side. Raise the Handle to go right. Lower the Handle to go left. CAUTION! Immediately start moving the machine back and forth. Keep the machine moving while the motor is running to avoid damage to the floor. 4 Hold one of the Operator Hand Grips (1) firmly, push the Safety Lock Button (2) and then compress the Switch Levers (3) to start the motor. NOTE: When the Switch Levers (3) are released, the machine shuts off immediately. AFTER USE (Figure 4) 1 Place the Operator Handle (6) in the upright position and unplug the Power Cord (5). Wrap the Power Cord (5) around the Operator Handle Grips (1) and the Cord Hook (7). 2 Remove the pad driver from the machine. Never store the machine with the pad driver on the machine. 3 Wipe the entire machine with a clean, damp cloth. 4 Inspect the entire machine and all accessories for damage. Perform any required maintenance or repairs before storage. 5 Store the machine in a clean, dry place with the Operator Handle (6) locked in the upright position. 4 3 5 7 2 6 8 1 Figure 4 -8- Clarke® American Sanders Operator's Manual (EN) - RS-16 /RS-16DC ENGLISH EN TROUBLESHOOTING MACHINE WOBBLES DURING OPERATION • Defective pad... one side is more dense than the other. • Machine left sitting on pad for extended period of time causing pad to “take a set”. • Pad not “seated” properly into pad holder bristles. • Warped block on brush or padholder - replace. MACHINE DOES NOT RUN • Check plug for proper connection - on machine and at wall outlet. • Check building circuit breaker. • Call for service. Clarke® American Sanders Operator's Manual (EN) -RS-16 /RS-16DC - 9 RS-16 RS-16 DC Section II Parts and Service Manual (71121A) Clarke® American Sanders Operator's Manual - RS-16 /RS-16DC - 27 - RS-16, RS-16 DC Assembly Drawing 1/06 -28- Clarke® American Sanders Operator's Manual - RS-16 /RS-16DC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 35 34 36 37 38 39 4 40 Ref. Part No. Description Qty. Qty. 1 71119A Label 1 1 2 21074A Handle Front 1 1 3 10687A Module 1 1 4 80290A Screw, 10-32 x 3/8 4 4 5 80291A Washer, #10 1 1 6 21075A Handle Back 1 1 7 80284A Screw, 10-32 x 3/4 6 6 8 61373A Handle Tube 1 1 9 10304A Adaptor - 1 10 85815A Screw, 5/16 x 1. - 1 11 Ref.* Bushing (Equipped with 40789A) 1 1 12 40789A* Cord Interconnect 1 1 13 40919A Cord, Power 1 1 14 30407B Hose, Squeegee - 1 15 980648 Washer, . 2 2 16 80295A Washer, Bowed 2 2 17 53833A Pin, . 2 2 18 61725A Axle 1 1 19 61832A Shield, Inner - 1 20 30725A Skirt - 1 21 10242A Pad Driver 1 1 NI 460215 Hard Plate (Option 1) 1 1 22 30381A Bumper 1 1 23 80294A Screw, 5/16 4 - 80305A Screw, 5/16 x 2 - 4 24 67890A Spacer, 7/8 x 9/16 x 5/16 - 4 25 61826A Shield (with connector) - 1 61715A Shield 1 - 26 21088A Main Frame 1 1 27 53650A Motor 1 1 28 70499A Label 1 1 29 39857A Wheel 2 2 30 80292A Screw, .-20 x 1 2 2 31 56057675 Grip Handle 1 1 32 53662A Pin, . 1 1 33 461404 Cam, Locking 1 1 34 441301 Bolt, Locking Cam 1 1 35 980341 Washer 1 1 36 50781A Clamp 1 1 37 920342 Nut, 3/8 1 1 38 61716A Cover 1 1 39 71120A Label 1 1 40 920110 Nut, 5/16 - 1 RS-16, RS-16 DC Assembly Drawing Parts List 1/06 Clarke® American Sanders Operator's Manual - RS-16 /RS-16DC - 29 - RS-16 RS-16 DC RS-16, RS-16 DC Motor Assembly Drawing, Parts List and Schematics 1/06 VOLTS / Hz 120 / 60 MOTOR PART NUMBER 40763A Part No. Description Qty 53193A Rotor, 1.5HP, 60Hz 1 40694A Capacitor, Start 1 53191A Capacitor, Run 1 53189A Stator, 1.5HP, 60Hz 1 53360A Cover, Capacitor 2 40699A Cover, Wiring 2 53190A Switch, Start 2 53195A Centrif...
Otros modelos de este manual:Máquinas de rectificar - RS-16 (1 mb)