Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
4. Remove adjusting keys or wrenches before turning the tool ON. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury. 5. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enable better control of the tool in unexpected situations. 6. Use safety equipment. Always wear eye protection. Dust mask, nonskid safety shoes, hard hat, or hearing protection must be used for appropriate conditions. TOOLS USE AND CARE 1. Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. 2. Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. 3. Do not use tool if switch does not turn it ON or OFF. A tool that cannot be controlled with the switch is dangerous and must be repaired. 4. Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally. 5. Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users. 6. Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control. 7. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. 8. Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may become hazardous when used on another tool. SERVICE 1. Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel may result in a risk of injury. 2. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance Section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury. 3 900006 - 02-07-02.qxd 10/15/02 2:25 PM Page 4 SPECIFIC SAFETY RULES AND SYMBOLS FOR RANDOM ORBIT SANDERS 1. ALWAYS DISCONNECT the sander cord plug from the power circuit before changing abrasive sheets. 2. USE DUST MASK. Wear a protective mask to minimize breathing in the fine dust created while sanding. 3. DO NOT RUN TOOL WITH BACK-UP PAD REMOVED. Resulting vibration could cause loss of control. 4. DO NOT OPERATE TOOL WITH DUST SHROUD REMOVED. The dust shroud covers high-speed rotating parts. 5. KEEP HANDS AND BODY PARTS AWAY from rotating disc. Contact with rotating disc may cause severe cuts and abrasions. 6. NEVER RUN SANDER with dust container or dust collector assembly removed. Dust could be blown into eyes. 7. WEAR EYE AND FACE PROTECTION. Injury to face and eyes can result if disc flies off or pad ruptures. Wear impact resistant glasses and full face shield. 8. USE PROPER SAFETY EQUIPMENT. Wear safety goggles to protect your eyes and wear a protective mask to minimize breathing in the fine dust created while sanding. NOTE: Some wood contains preservatives which can be toxic. Take extra care to prevent inhalation and skin contact when working with these materials. 9. SANDING OF LEAD-BASED PAINT IS NOT RECOMMENDED. Lead- based paint should only be removed by a professional. 10. SOME WOOD CONTAINS PRESERVATIVES WHICH CAN BE TOXIC. Take extra care to prevent inhalation and skin contact when working with these materials. Request, and follow, any safety information available from your material supplier. 11. WARNING: There are certain applications for which this tool was designed. Porter-Cable strongly recommends that this tool NOT be modified and/or used for any application other than for which it was designed. If you have any questions relative to its application DO NOT use the tool until you have written Porter-Cable and we have advised you. Technical Service Manager Porter-Cable Corporation 4825 Highway 45 North Jackson, TN 38305 SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts .F ........................ microfarads l ........................ liters kg ........................ kilograms N/cm2 ........................ newtons per square centimeter Pa ........................ pascals h ........................ hours min ........................ minutes s ........................ seconds 4 900006 - 02-07-02.qxd 10/15/02 2:25 PM Page 5 3 3N ........................ alternating current ........................ three-phase alternating current ........................ three-phase alternating current with neut...
Otros modelos de este manual:Máquinas de rectificar - 332 (241.1 kb)
Máquinas de rectificar - 334 (241.1 kb)