Votos - 5, Puntuación media: 4
(
)
)
|
Resumen del manual
21. NEVER ALLOW UNTRAINED USERS TO USE THIS TOOL WHILE UNSUPERVISED. 22. IF YOU ARE UNSURE OF THE INTENDED OPERATION, STOP USING TOOL. Seek formal training or research books or magazines that specialize in pneumatic tools. 23. BE AWARE OF HOSE LOCATION. Hoses can easily become a tripping hazard when laid across the floor in a disorganized fashion. 24. DO NOT USE UNDER THE INFLUENCE OF DRUGS OR ALCOHOL, OR WHEN TIRED. No list of safety guidelines is complete, because every work environment is different. Always consider safety first and use common sense. Failure to use this tool with caution and respect could result in serious personal injury. -2- Model H8215 6" Dual Action Air Sander INTRODUCTION Foreword The specifications, details, and photographs in this manual represent the Model H8215 as supplied when the manual was prepared. However, owing to Grizzly’s policy of continuous improvement, changes may be made at any time with no obligation on the part of Grizzly. If you have any comments regarding this manual, please write to us at the following address: Grizzly Industrial, Inc. C/O Technical Documentation P.O. Box 2069 Bellingham, WA 98227-2069 E-Mail: manuals@grizzly.com Most importantly, we stand behind our tools. If you have any service questions or parts requests, please call or write us at the location listed below. Grizzly Industrial, Inc. 1203 Lycoming Mall Circle Muncy, PA 17756 Phone: (570) 546-9663 Fax: (800) 438-5901 E-Mail: techsupport@grizzly.com Web Site: Specifications Sanding Pad............................................6" No Load Speed.......................10,000 RPM Air Consumption...............................4 CFM Air Inlet.....................................................1.4" Required PSI.....................................90 PSI Maximum Sound Level......................84 dB Sandpaper Type....................................PSA Inventory A. Dual Action Air Sander B. Oil Bottle C. 1/4" NPT Male Quick Connect Fitting D. 6" Sanding Disc A B C D Figure 1.Model H8215 Inventory. Model H8215 6" Dual Action Air Sander -3 -4- Model H8215 6" Dual Action Air Sander OPERATIONS Read the manual before operation. Become familiar with this tool, its safety instructions, and its operation before beginning any work. Serious personal injury may result if safety or operational information is not understood or followed. Figure 2. Attaching sanding disc. Like all tools there is potential danger when operating this tool. Accidents are frequently caused by lack of familiarity or failure to pay attention. If normal safety precautions are overlooked or ignored, serious personal injury may occur. To set up the Model H8215 Air Sander: 1. DISCONNECT THE SANDER FROM THE AIR SUPPLY! 2. Firmly holding the orbital shaft, rotate the spindle swivel lock against one of the spindle flats. 3. Thread the sanding pad onto the drive spindle. 4. Install the 1.4" NPT male quick-connect fitting into the air inlet. 5. Attach a 6" pressure sensitive adhesive (PSA) sanding disc to the sanding pad, as shown in Figure 2. Orbital Shaft Swivel Lock Model H8215 6" Dual Action Air Sander -5- Operation 1. Connect the tool to compressed air regulated at 90 PSI. 2. Hold the sander firmly and press the throttle lever (Figure 3) to turn it ON. Daily Maintenance The dual action sander MUST have 2-6 drops of oil directly dropped into the air fitting before and after each use. A filter regulator set up is recommended, however an in-line lubricator is not recommended as excess oil in the tool could spray onto the workpiece. Run the sander for a few minutes to eject excess oil, then wipe the tool down with a rag and begin sanding. Oil the tool after use or storage. These procedures should be done after each use: • Wipe the housing and tool bits with a dry cloth, or blow off the dust and debris with compressed air. • Check for damage to tooling, hoses, housing or other accessories. ACCIDENTAL START HAZARD! Disconnect before service or tool changes. AIR PRESSURE HAZARD! Never exceed 120 PSI. LUNG/EAR INJURY HAZARD! Wear protective equipment when using this tool. EYE INJURY HAZARD! Wear protective equipment when using this tool. 3. Turn the regulator knob (Figure 3) to adjust the speed of the sanding disc. 4. Remove pressure on the throttle lever to stop the sander. 5. When the sandpaper loses its effectiveness, remove sandpaper from the pad and install a new disc. 6. To avoid accidental starting, disconnect the sander from the air supply when it is not in use or when performing maintenance. Throttle Lever Regulator Knob Figure 3. Sander controls. H8215 PARTS LIST .............................................................................................................................. ............................................................................ REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PSB48M CAP SCREW M6-1 X 35 2 PLW03M LOCK WASHER 6MM 2-1 PW03M FLAT WASHER 6MM 3 PH8215003 WAVY WASHER 6MM 4 ...