Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Box Size......................................................................................23" L x 12" W x 10" H Footprint ..............................................................................................................6" x 9" Construction: Base ......................................................................................................................Steel Table (Belt) ........................................................................................Ground Cast Iron Table (Disc)............................................................................................Stamped Steel Miter Gauge................................................................Die Cast Plastic / Aluminum Bar Motor: Type ............................................................................TEFC Capacitor Start Induction Horsepower..........................................................................................................1.2 HP Phase / Voltage............................................................................ Single Phase . 110V Amps............................................................................................................................3 Cycle . RPM..................................................................................60 Hertz . 3450 RPM Switch ..........................................................................................Toggle Safety Switch Power Transfer ..........................................................................................Direct Drive Bearings ........................................................Shielded & Permanently Lubricated Ball Specifications, while deemed accurate, are not guaranteed. REVISED 4/99 G3105 Combination Sander -17 DIAGRAMS & PARTS LISTS G3105 MOTOR B & TCAPACITORS 43 42 44 27 40 44 10 65 3 1 7 2 3 4 4 6 8 11 48 12 19 13 71 14 57 55 57 55 16 18 17 15 64 46 57 47 58 9 45 REF PART DESCRIPTION REF PART DESCRIPTION 1 P3105001 ROTOR 2 P3105002 STATOR 3 P6202 BALL BEARING 6202 4 P3105004 MOTOR END BELL 6 P3105006 CAPACITOR 7 P3105007 CAPACITOR CLIP 8 P3105008 BOTTOM COVER 9 P3105009 RUBBER FOOT 10 P3105010 DISC GUARD 11 P3105011 DISC GUARD BRACKET 12 P3105012 SANDING PLATE 13 P3105013 DISC TABLE 14 P3105014 LEFT TRUNNION 15 P3105015 TABLE SUPPORT BRACKET 16 P3105016 RIGHT TRUNNION 17 P3105017 KNOB 18 P3105018 GUIDE PIN 19 G1445 6" 60-GRIT DISC (3) PACK 20 P3105020 BELT HOUSING 21 P3105021 STOP BRACKET 22 P3105022 DRIVE WHEEL 23 P3105023 WHEEL FLANGE 24 PN06 HEX NUT 1/2" - 12 25 P3105025 BELT PLATEN 26 P3105026 GUARD SUPPORT 27 PB02 HEX BOLT 1/4" - 20 x 5/8" 28 P3105028 BELT GUARD 29 G1209 1"X42" 100-GRIT (2) PACK 30 P6200 BALL BEARING 6200 31 P3105031 TRACKING WHEEL 32 P3105032 TRACKING SHAFT 33 P3105033 TRACKING BRACKET 34 P3105034 TENSION SPRING -18-G3105 Combination Sander G3105 SAND FRAME 17 17 48 36 59 37 34 51 56 33 61 32 20 30 31 30 60 26 57 55 29 25 23 24 22 26 49 50 35 4521 38 53 39 69 67 54 52 72 62 28 REF PART DESCRIPTION REF PART DESCRIPTION 35 P3105035 SPRING PLATE 36 P3105036 SPRING CAP 37 P3105037 HANDLE W/KNOB 38 P3105038 BELT TABLE 39 P3105039 BELT TABLE BRACKET 40 P3105040 SWITCH 41 PS01 PHLP HD SCREW 10 - 24 x 1/2" 42 P3105042 STRAIN RELIEF 43 P3105043 POWER CORD 44 PS06 PHLP HD SCREW 10 - 24 x 3/8" 45 PS01 PHLP HD SCREW 10 - 24 x 1/2" 46 PB09 HEX BOLT 5/16" - 18 x 1/2" 47 P3105047 HOUSING SCREW 48 PSS04 SETSCREW 1/4" - 20 x 5/16" 49 PSB02 CAP SCREW 10 - 24 x 3/8" 50 PSB31 CAP SCREW 10 - 24 x 5/8" 51 PSB33 CAP SCREW 10 - 24 x 3/4" 52 PSB16 CAP SCREW 3/8" - 16 x 3/4" 53 PFH06 FLAT HD SCREW 5/16" - 18 x 7/8" 54 PW02 FLAT WASHER 3/8" 55 PB19 HEX BOLT 1/4" - 20 X 1/2" 56 PN07 HEX NUT 10 - 24 57 PW06 FLAT WASHER 1/4" 58 PLW03 LOCK WASHER 3.16" 59 PN05 HEX NUT 1/4" - 20 60 PR01M EXT RET RING 10mm 61 PR05M EXT RET RING 15mm 62 PSB19 CAP SCREW 3/8" - 16 x 1 1/4" 64 PW07 FLAT WASHER 5/16" 65 P3105065 MOTOR SHROUD 67 PN02 HEX NUT 5/16" - 18 69 P3105069 SPACER 71 P3105071 MITER GAUGE 72 PLW04 LOCK WASHER 3/8" G3105 Combination Sander -19 TROUBLESHOOTING SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION Motor will not start. 1. Low voltage. 2. Open circuit in motor or loose connections. 1. Check power line for proper voltage. 2. Inspect all lead connections on motor for loose or open connections. Motor will not start; fuses or circuit breakers blow. 1. Short circuit in line cord or plug. 2. Short circuit in motor or loose connections. 3. Incorrect fuses or circuit breakers in power line. 1. Inspect cord or plug for damaged insulation and shorted wires. 2. Inspect all connections on motor for loose or shorted terminals or worn insulation. 3. Install correct fuses or circuit breakers. Motor fails to develop full power (power output of motor decreases rapidly with decrease in voltage at motor terminals). 1. Power line overloaded with lights, appliances, and other motors. 2. Undersized wires or circuits too long. 3. General overloading of power company facilities. 1. Reduce load on power line. 2....