Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
4. The sander is now ready to use. OPERATING THE PAD SANDER Disconnect the power plug from the AC power source before any assembly, adjustments, or adding/removing accessories. Following this preventative step reduces the risk of the sander coming on accidentally and the risk of damage to the workpiece and injury to the operator. Remove components from carton and examine contents carefully. Do not discard carton and packing until components are examined. 10 2. Push the Dust Collector all the way into the opening at the rear of the sander. The collector should fit snug in the adapter. If the collector is not held firmly in place, replace the "O" ring. INSTALLING THE SANDPAPER INSTALLING THE SANDPAPER: The Pad Sander uses 1/4-sheet size sandpaper. It is held in place by two clamps on each end of the sander. Depress the clamp release lever on one end and slide the sandpaper under the clamp. Repeat for the other end to complete installing sandpaper. ABRASIVE DISKS: Only use Abrasive Disks having a hook and loop fastening system and with holes that match the holes on the bottom of this sander. Sandpaper Clamp Sandpaper Sandpaper Clamp Release Lever Punchplate Sandpaper Dust Collection Bag Sandpaper Clamp FIGURE 4. USING THE SANDPAPER PUNCHPLATE FIGURE 3. INSTALLING THE SANDPAPER "O" Ring Dust Collection Bag Push all the way in for a snug fit FIGURE 2. ATTACHING THE DUST COLLECTION BAG USING THE PAD SANDER: 1. Prepare the workpiece according to instructions in this manual. 2. Plug the sander into an approved power source. 3. Turn on the sander by depressing the ON/OFF switch on the front. 4. Hold the sander against the workpiece with a firm grip. 5. Sand the workpiece in a circular motion. Using a straight in-line motion can cause uneven patterns to result. Do not hold the Pad Sander in one spot for prolonged periods. This can cause the sander to overheat as well as causing scorching on the workpiece. Damage to the Pad Sander and workpiece could result. Always wear approved safety eyewear and appropriate dust filters or respirators when using this tool. MAINTENANCE AND CLEANING CLEANING: To avoid accidents, be sure to disconnect the tool from the electrical power source before any cleaning or maintenance. The tool can be cleaned by using compressed dry air. If compressed air is not available, a soft natural bristle paint brush will work. Always wear safety goggles when cleaning tools with compressed air. Avoid using certain cleaning agents and solvents. Chemicals like gasoline, carbon tetrachloride, acetone, paint thinner or ammonia products can damage the plastic parts of the tool. ACCESSORIES Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may become hazardous when used on another tool. Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets. If you must use an extension cord, be sure that the gauge is large enough to carry the amount of current necessary for your power tool. If not, your tool may experience a loss of power, excessive voltage drop or overheating. The smaller the gauge number, the heavier the cord (see table on next page). RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS TOOL CURRENT RATING CONDUCTOR SIZE IN A.W.G AMPERE 10FT. 25FT. 50FT. 100FT. 3-6 18 18 18 18 6-8 18 18 18 16 8-10 18 18 18 14 10-12 16 16 14 14 12-16 14 12 12 - 16-20 12 12 12 - SPECIFICATIONS SPECIFICATIONS Voltage 120V 60 Hz Rated Current 1.3 A Diameter of Orbit 1.587mm (1/16") No-Load Speed 10000/min OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would like further information on the following products, please contact Alltrade Customer Service Department at 1-800-590-3723. Cordless Drills/Screwdrivers Impact Wrenches Sanders Jigsaws Circular Saws 11 Angle Grinders Hold the Pad Sander firmly by the top Always sand in a circular motion FIGURE 5. USING THE PAD SANDER Reciprocating Saws Routers Rotary Tools Corded and Cordless Multi-Purpose Tools Wide Range of Accessories and more item and/or part will be repaired and/or replaced. If the unit is repaired, new or reconditioned replacement parts may be used. If Alltrade chooses to replace the product, it may replace it with a new or reconditioned one of the same or comparable design. The repaired or replaced unit will be warranted under the terms of the remainder of the warranty period. Typically, a defective product that is returned within the first 30 days after the purchase date will be replaced; for items returned after the first 30 days and within the warranty period, covered defective parts not subject to normal wear and tear or other exclusions will be repaired or replaced, at Alltrade’s option. During the warranty period, Alltrade will be responsible for the return shipping charges. Alltrade’s repair and/or replacement of any nonconforming item and/or part thereof shall constitute fulfillment ...