Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
White Polish Pad 4. Floor finish liquid 5. Clean string mop, 16-20 oz. size 6. Bucket and wringer 7. Disposable plastic bag PROCEDURE: 1. Place disposable bag inside of bucket with wringer. This will protect floor finish from being contaminated and chemical residue remaining in bucket. 2. Pour quart size container of floor finish into the disposable bag. Amount of floor finish depends on size of floor area to be covered and number of coats to be applied. 3. Dip the mop tip ONLY into the floor finish and wring out lightly. Avoid dripping floor finish or splashing on walls. 4. Apply floor finish in thin even coats. Apply FIRST COAT of floor finish along baseboard edges and cover remaining floor area in an east-west direction. HINT: Only first coat of floor finish need be applied to baseboard edges. 5. Allow floor finish to dry 20 minutes before applying second coat. 6. Apply second coat of floor finish 1 tile width out from baseboard. Application should be in a crossing direction to the preceding coat. 7. Additional coats (3 and 4) of floor finish should be applied to achieve the level of appearance desired. Four coats of floor finish will provide extra protection to the floor surface. 8. Allow 24 hours for floor finish to harden before buffing. 9. Buff floor to higher shine using Orbiter, Drive Pad Holder and white polish pad. PRECAUTIONS: 1. When using NEW mops to apply floor finish, make sure to rinse mop first. Foreign chemicals will affect the floor finish. 2. Completely submerging mop head into the floor finish is a waste of product. 3. Turn mop over frequently for even distribution of floor finish. 4. Do not allow mop to become dry; this will cause streaking. 5. Apply floor finish in thin even coats. 6. Do NOT pour floor finish and attempt to spread evenly. This will cause dark spots and delay drying time. 6 Stripping Procedure Bonnet Cleaning Procedure Residential Use This procedure can be used on most types of hard floor surfaces, EXCEPT WOOD FLOORS. EQUIPMENT AND MATERIALS REQUIRED: 1. Orbiter floor machine 2. Drive pad holder 3. Black strip pad or brown scrub pad 4. Broom or dust mop 5. Wax remover or stripping solution 6. Small black pad -HINT: Use “donut hole” from black or brown pad. 7. Mops - 2 each (1 to apply/pick up stripping solution and 1 to rinse floor) 8. Bucket and wringer 9. Wet-dry vacuum (for dirty and rinse water pick-up) PROCEDURE: 1. Sweep floor area to be stripped (broom or dust mop). 2. Mix stripping solution according to manufacturer’s instructions on container label for proper solution mixture. 3. Dip mop in stripping solution and apply to floor in a 6’ x 6’ area. Apply along baseboard edges first or where there is a wax or dirt build-up. 4. Let solution stand for 5 minutes, scrub floor with Orbiter floor machine, pad holder and black or brown pad. Use small black pad, “donut hole,” to reach in corners and around door jambs. 5. To pick up dirty solution, use a mop or wet-dry vacuum. DO NOT ALLOW STRIPPING SOLUTION TO DRY ON FLOOR. 6. Repeat steps 3-5 until all floor area is completely stripped. 7. Rinse area TWICE with clean water and clean mop. Pick up water with mop or wet-dry vacuum. 8. Allow floor to dry before applying new floor finish. PRECAUTIONS: 1. Do not flood the floor with stripping solution or allow solution to dry before pick-up. 2. Use clean mop for final rinse. 3. Change rinse water frequently. 4. Use damp cloth to wipe off any splashes on walls or furniture. CARPET BONNET CLEANING PROCEDURE This procedure can be used on most types of carpets. METHOD 1 - FOR SPOTS OR SMALL AREAS EQUIPMENT AND MATERIALS REQUIRED: 1. Orbiter floor machine 2. Drive pad holder 3. Carpet bonnet 4. Oreck Soil Release Spray PROCEDURE: 1. Lightly spray Soil Release over spot in carpet or high traffic area. 2. Place pad holder on Orbiter and center on top of carpet bonnet. 3. Work carpet bonnet over treated area. 4. Turn carpet bonnet over when soiled and continue to clean carpet. 5. When job is complete, clean carpet bonnet in washing machine or hose off and allow to air dry. METHOD 2 - FOR LARGE TRAFFIC AREAS EQUIPMENT AND MATERIALS REQUIRED: 1. Orbiter floor machine 2. Drive pad holder 3. Carpet bonnet 4. Liquid shampoo 5. Bucket and wringer PROCEDURE: 1. Mix liquid shampoo in bucket according to manufacturer’s instructions. 2. Soak carpet bonnet in shampoo mix. 3. Wring out carpet bonnet until damp and place on carpet. 4. Center Orbiter with pad holder on carpet bonnet. 5. Turn machine on. Work carpet bonnet over soiled area. 6. When carpet bonnet becomes dry, repeat Steps 2-5 until carpet area is cleaned. 7. When job is complete, clean carpet bonnet in washing machine or hose off and allow to air dry. 7 AccessoriesHard Floor Cleaning HEAVY-DUTY CLEANING FOR HARD SURFACE FLOORS (except wood and marble) EQUIPMENT AND MATERIALS REQUIRED: 1. Orbiter floor machine 5. Oreck O Monster® All Purpose Cleaner 2. Black Drive Pad Holder 6. Broom or Dust Mop 3. Brown Pad 7. Cleaning Solution 4. ...