Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
• Do not use the shredder for anything other than its intended purpose (shredding paper documents). Do not shred cloth, plastic, cardboard, or any other hard material that will damage the shredder blades. Remove all paper clips and staples from paper before shredding. • Do not place hands or fingers into the shredder feed opening as serious injury may result. • Follow all warnings and instructions marked on the shredder. • This product should not be placed near, or over, a heat source. • Do not use this product near water or in areas of high humidity and avoid spilling liquids on it. • To stop shredding in case of emergency, unplug the shredder immediately. For this reason, make sure the outlet that the shredder is connected to is easily accessible. • Do not leave the power cord where something may be placed on it, or it may be stepped on. • This unit should not be operated or stored near children or pets. • Always unplug the shredder prior to moving, cleaning or emptying the wastebasket. • The use of an extension cord is not recommended. PLEASE SAVE THESE INSTRUCTIONS TO GET THE MOST OUT OF YOUR SHREDDER: • Never try to shred more than the shred capacity. Overloading the shredder will shorten its durability. • Always feed the paper(s) in straight, do not feed at an angle. • Clean the outside of the shredder by wiping it with a damp cloth from time to time. Mild stains can be removed using a soft, damp cloth and mild detergent. Remove detergent residue with a damp cloth. Always unplug the shredder before cleaning. • Never use any harsh or abrasive cleanser. • Keep the shredder away from direct sunlight. 2 MPS1440.O/M.QXD 8/12/02 11:33 AM Page 3 POWER SOURCE AC USAGE Use the AC polarized line cord included with the unit for operation on AC power. Insert the plug into a conveniently located AC outlet having 120V, 60 Hz. NOTE: The AC plug supplied with the unit is polarized to help minimize the ACPlugACOutlet possibility of electric shock. If the AC plug does not fit into a nonpolarized AC outlet, do not file or cut the wide blade. It is the user’s responsibility to have an electrician replace the obsolete outlet. LOCATION OF CONTROLS 1 2 3 1. Function (ON/AUTO,FWD,REV) Switch 2. Shredder 3. Adjustable Arm 3 MPS1440.O/M.QXD 8/12/02 11:33 AM Page 4 OPERATION INSTALLATION: To install the shredder, make sure the unit is unplugged and simply slide the Adjustable Arm out to fit the wastebasket. Follow the instructions below to operate your new shredder. After unpacking the shredder, place it securely on the supplied wastebasket. Then, plug the unit into an AC outlet as described on page 1. 1 2 Slide the Function switch to the Insert up to 5 pages of 20lb paper ON/AUTO or the FWD position. into the shredder, and the unit will automatically shred them. NOTES: • If inserting small documents, insert them in the center of the shredder as the sensor is located there. • Do not attempt to insert more than 5 pages at a time, as it will shorten the life of the shredder. • The shredder will stop automatically if it is overheated by long and continuous intermittent operation. Allow the shredder to rest for approximately 20 minutes to cool down. 4 MPS1440.O/M.QXD 8/12/02 11:33 AM Page 5 OPERATION REMOVING PAPER JAMS: PAPER TIP SOLUTION If a paper jam occurs, slide the Function switch to the REV (Reverse) position to withdraw the non-shredded paper. 1 On occasion, paper strips get stuck in the shredder. In this case, slide the Function switch to the REV position for 2 to 3 seconds. Then, slide the Function switch back to the ON/AUTO or the FWD position. Repeat this procedure one to two times to fully clear the paper tips. 1 SPECIFICATIONS Power Source......................................................120V AC, 60Hz Shred capacity...............................5 single sheets of 20lb paper Shred Size............................................................................7mm Paper Cut.......................................................................Strip-Cut 5 MPS1440.O/M.QXD 8/12/02 11:33 AM Page 6 TROUBLESHOOTING GUIDE Before requesting service, please refer to the following troubleshooting guide. Many questions/problems you may be having will be answered simply. SYMPTOM SOLUTION Shredder does not run. Power cord is not plugged in. The inserted paper(s) are beyond the shredder capacity. Use 5 or less pages at once. The motor is overheated due to continuous shredding. Do not use shredder for 20 minutes. Shredder running, but no Empty wastebasket as it is full. paper is inserted. Paper is stuck in the shredder, clear the them from the shredder. When inserting envelopes or The width of the pages is not wide enough to similar small pages, the touch the sensor at the center of the shredder. shredder does not activate. FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE, PLEASE VISIT OUR WEBSITE AT WWW.MEMCORPINC.COM OR CONTACT CUSTOMER SERVICE AT 1-800-919-3647 FOR PARTS & ACCESSORIES, CONTACT FOX INT’L AT 1-800-321-6993. 6 MPS1...