Votos - 1, Puntuación media: 5
(
)
)
|
Resumen del manual
To ensure sufficient ventilation of the shredder a minimum distance of 4" (10 cm) to the wall or to the furniture must be maintained. 6. Caution Never insert hand, fingers or any foreign objects into the feed opening. Serious injury may result. Keep all loose articles of clothing, ties, jewelery, long hair or other loose objects away from feed opening. Injury may result. Always turn off and unplug the machine before moving, servicing, cleaning or any other conduct other than normal operation. Serious injury may result. 7. Operation Read operating instructions before putting shredder into operation Insert plug in power outlet Install waste bag for shredded material – Open front door and completely remove bag frame from cabinet – Fold new bag around frame. Allow bag to overhang frame by appoximately 7" (20 cm). – Slide frame with bag back into cabinet – Close cabinet door. Switching equipment on 0 I – Set main power switch (located on back of shredder) to ON (1) position. – (On the 520 HS, the security key lock switch must also be turned on) Green LED lights • Equipment is ready for operation (standby) To shred paper – Press green arrow button at least 4 sec • Cutting system runs in forward direction – Insert paper into the paper feed opening • Shredding occurs or – Feed paper • The shredding process is started by a photo– cell in the paper feeding opening When the paper feeding opening is free again, the cutting system automatically switches off after approx. 3 sec. and returns to standby. When shredding is completed – Push stop button • Cutting system stops • Equipment returns to "ready-to-operate" (standby) condition Switching equipment off 0 I – Set main power switch (located on back of shredder) to OFF (0) position. Edition 01/03 Paper shredder 520C Feeding continuous forms – Pass the leading edge of the form under the paper guide roller (1) and into the paper feed opening (2). 12 8. Malfunctions Paper jam Red LED on keyboard lights • Shredder reverses automatically and runs in this mode for a few seconds. • Pull out jam and remove excess paper. Caution! Do notattempt to force the jammed material through the machine by alternating the cutting system between forward and reverse. If paper jam cannot be removed • Hold down reverse button until paper can be pulled out of the cutting system. • Press green arrow button at least 4 sec • Continue shredding in smaller quantities so as not to jam the machine further. or • Continue shredding in smaller quantities so as not to jam the machine further. • The shredding process is started by a photo–cell in the paper feeding opening Electronic motor overheated Red LED on keyboard lights • Shredder switches off automatically. • Allow shredder to cool down for approx. 15-20 min. – Press green arrow button at least 4 sec Cabinet door contact ajar / bag full Red LED lights • Shredder switches off automatically. • Make sure cabinet door is properly closed and/or empty waste container. – Press green arrow button at least 4 sec 9. Maintenance (Cross cut unit only) – When shredding capacity drops or the noise increases. • Apply oil over full width of cutting cylinders through the paper entry (Fellowes Powershred Lubricant # 35250). CAUTION: Do not use flammable synthetic oil, petroleum-based products, or aerosol lubricants of any kind. • Run cutting system forward and backward several times without feeding paper. • Continue shredding. 10. Checklist for Inoperative Machine If the equipment does not work properly, please check the following points first: – Is the plug inserted? – Is the switch turned on? – Is the cabinet door closed? – Is the waste receptacle full? Empty waste bag. – Is there a paper jam in the shredder? See Malfunctions – Is the motor overheated? Switch machine off and allow motor to cool down for approximately 15-20 min. If none of the above applies and the equipment still does not run, please contact our customer service department. Edition 01/03 520C Paper shredder 11. Warranty Limited Warranty Fellowes, Inc. warrants the cutting cylinders of the machine to be free from defects in material and workmanship for 20 years from the date of purchase by the original consumer in the case of models 320, 320C, 380, 380C, 420, 420C, 520 and 520C or 5 years from the date of purchase by the original purchaser in the case of models 320HS, 420HS and 480HS. Fellowes warrants all other parts of the machine to be free of defects in material and workmanship for 2 years from the date of purchase by the original consumer (applies to all models covered in this manual). If any part is found to be defective during the warranty period, your sole and exclusive remedy will be repair or replacement, at Fellowes’ option and expense, of the defective part. This warranty does not apply in cases of abuse, mishandling or unauthorized repair. ANY IMPLIED WARRANTY, INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION TO THE APPROPRIATE WARRANTY ...
Otros modelos de este manual:Trituradora, - 520C (138.11 kb)