Votos - 2, Puntuación media: 3 ( )

Fabricar: Fellowes Tamaño del archivo: 79.74 kb Nombre del archivo: Idioma del manual:

• Return wastebox, close door and resume operation. Door Ajar: • Make sure door is completely closed. • If the door is opened while the motor is running, after closing the door, set the rocker switch to the “O” position and then to the “I” position to resume operation. 220, 220CC, 280, 280CC If only the green light is on: Paper Jam: • Press rocker switch to “O” to stop the cutting system. • Press and hold down rocker switch in “R” to reverse the cutting system and back out jammed material (paper is pushed out) • If the jam persists, slowly move the power switch back and forth between forward (I) and reverse (R), always stopping for a moment in the off position (O). Do not switch the shredder rapidly between forward and reverse to force material through the shredder. Rapid rocking develops tremendous forces that can damage your shredder. • Continue shredding in smaller quantities so as not to jam the machine further. Overheated: • If the motor is overheated, switch the machine off and allow motor to cool down for approximately 1520 minutes. 320,320CC, 380, 380CC If no lights are on: • Make sure the circuit breaker is not open. (press to reset). If only the red light is on: Paper Jam: • Press rocker switch to “O” to stop the cutting system. • Press and hold down rocker switch in “R” to reverse the cutting system and back out jammed material (paper is pushed out). Rocker switch must be held in reverse for a few seconds to cause the red light to turn off. • If the jam persists, slowly move the power switch back and forth between forward (I) and reverse (R), always stopping for a moment in the off position (O). Do not switch the shredder rapidly between forward and reverse to force material through the shredder. Rapid rocking develops tremendous forces that can damage your shredder. • Continue shredding in smaller quantities so as not to jam the machine further. Overheated: • If the motor is overheated, switch the machine off and allow motor to cool down for approximately 1520 minutes. Maintenance (Cross Cut Units Only) Shredder Oiling Instructions When shredding capacity drops, noise increases, or if the cutting cylinders stop with a squeak or a rubbing sound, the cutters should be oiled. • When lubricating the cutters, utilize POWERSHRED lubricant #35250 or a suitable substitute, i.e., a light weight machine oil or a sewing machine oil. Do not spray an aerosol cleaner or lubricant into the machine. Some agents may combust, causing serious injury. Make certain an extension nozzle is provided so the lubricant can reach well into the throat of the machine. • Squeeze the lubricant across the full width of the cutters and then turn the machine on and run the cutting system forward for a few seconds (the photo eye must be blocked with a piece of paper in order to run the cutting system forward). • Then depress the rocker switch in the reverse direction and run the cutting system in reverse for a few seconds. Repeat the procedure. Supplies • Bags for cut material (Packed in dispenser carton, 50 bags to a roll. Contact Fellowes or your local Fellowes dealer for the stock number of the bag that fits your machine.) • Cutting block oil for cross-cut units: Stock #35250 • Replacement wasteboxes and handles are available from Fellowes. Please call Fellowes customer service for ordering information. Warranty Fellowes Powershred Limited Warranty 1 year on all parts and labor 5 years parts and labor on cutting cylinders Fellowes warrants this product to be free from defects in material and workmanship for a period of one year from the date of purchase by the original consumer. At it’s option, Fellowes will repair or replace without charge for material or labor, any component found to be defective during the warranty period. Additionally, the cutting cylinders are warranted for 5 years from the original purchase date and will be replaced without charge for material or labor if found by Fellowes to be defective. Warranty Exclusions The parties agree that the buyer’s sole and exclusive remedy against Fellowes shall be for the repair or replacement of defective parts as provided herein. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to property or any other incidental or consequential loss) shall be available to him. This warranty shall NOT apply and is void under the following circumstances: 1. When this product or any part thereof has been subjected to accident, alteration, abuse, or misuse. 2. When the shredder's recommended sheet capacity (per specifications on page 5-6) has been exceeded (resulting in a paper jam). 3. When the original Model and Serial Number Plate has been altered, effaced or removed. 4. When repair or service covered under this warranty (other than routine maintenance as described in the Owner's Manual) has been performed by personnel without the express written consent of Fellowes. 5. When the product has been ...

Descargar ahora

Introduzca dos números de la imagen: