Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
3 Threading -Bobbin .............................. 4 -5 Top Thread ........................................ 6 Using the Controls Top Tension Control ........................... 7 -8 Adjusting Bobbin Tension ...................... 9 Stitch Length Control ............................ 10 Stitch Width Control ............................. 10 Reverse Stitch Control .......................... 11 Feed Dog Control ................................. 11 Special Stitch Dial ........................... 12-14 Pressure Regulator ............................... 15 Sewing Light ...................................... 16 Seam Guides ...................................... 17 Accessories Needles ............................................. 18 Needle, Thread, Fabric Chart .................. 19 Presser Feet ........................................ 20 Buttonhole Guide Feet .......................... 21 Zigzag and Straight Stitching Needle Plate ................................................. 22 Starting to Sew ..................................... 23 Garment Construction Stitches Straight Stitching ................................ 24 Zigzag Stitching .................................. 25 Stretch Stitching ............................ 26 -28 Special Finishing Stitches Satin Stitching, Appliqueing ................... 29 Buttonhole Making ......................... 30 -32 Button Sewing, Bar Tacking ................... 33 Blind Hemming .................. : ........... 34 -35 Zipper Application ................................ 36 Special Edge Stitch, Mending, Darning ..... 37 Checking Performance Problems ......... 39 -40 Caring for the Machine Cleaning Feed Dogs and Shuttle ................ 41 Oiling Under Arm Cover Plate .................... 42 Oiling Underside .................................... 43 Oiling Face Cover Plate ........................... 44 Parts List ........................................ 45 -46 69565 ,--_1. Knowing Your Sewing Machi FRONT VIEW . 2. 3. 4. 5. 6. 7. 8. 9. 10. 1 @ ® ® ® ® ® ® _ @ (_' Accessory Box Hinged Extension Needle Plate Zigzag Stitching Plate Presser Foot Thread Guide Thread Guide Thread Tension Regulator Thread Guide Face Cover Plate 11. Thread Guide 12. Take-up Lever 13. Top Thread Tension Control 14. Threading Path 15. Special Stitch Dial 16. Stitch Width Control 17. Reverse Stitch Control 18. Stitch Length Control 19. Nomenclature Plate @ @ © -@ @ BACK VIEW r @ ® @ .@ @ @ 7 @ @ ® / \ @ .@ 20. Light and Power Switch 26. Bobbin Winder Tension Disc 21. Connector 27. Thread Guide 22. Hand Wheel 28. Presser Foot Lever 23. Bobbin Winder Shaft 29. Thread Cutter 24. Bobbin Winder Latch 30. Needle Clamp Screw 25. Thread Spool Pin 31. Feed Dogs CONNECTING MACHINE ® % ®® ® 1. 2. Lift side For hinged extension at of machine bed-plate. more sewing space, the tip left the 4. Push the connector column. plug at the onto back three-prong of machine bed right plate edge cover up by pushing as shown in Fig. 2. 5. Plug 120 machine volt wall cord into outlet. any 110Turn on Turn you the accessory as shown in Fig. box 2. toward power switch. by pushing light and power 3. Fig. 3. shows the machine ready to sew with all the extensions in 6. Pull up machine. spool pin stored at top of place for maximum sewing space. _B WINDING THE BOBBIN ® ® ® ® , , Draw thread from spool through bobbin winder tension disc as shown in Fig. 1. Pull end of thread through hole in bobbin and place bobbin onto bobbin winder shaft with end of thread coming from the top of the bobbin, fitting the notch on the bobbin over locking stud on the shaft as shown in Fig. 2. Push bobbin winder latch against bobbin until it clicks. 4. Release clutch by pulling hand wheel or turning clutch knob as shown in Fig. 4. Start machine, holding onto end of thread. When bobbin is slightly filled, release end of thread. 5. When bobbin is full, winding mechanism stops. 6. Push in hand wheel or turning clutch knob to return to stitching position. Remove bobbin. . 4 THREADING THE BOBBIN CASE . \ ,ji_ k ,. ® I ® ® ® ® ® 1. To remove bobbin case from the . shuttle, raise needle to its highest position. 7. 2. Open bed plate cover, and remove 8. accessory box. , Pull open latch of bobbin case. 4. Pull bobbin case straight out of shuttle. . . Insert bobbin into bobbin case making sure thread is coming from bobbin as shown. Pull thread through slot of case as shown. Pull thread under tension spring. Holding latch open, position case into shuttle, and release latch. Case should lock into place when latch is released. Hold needle thread loosely in left hand and rotate hand wheel toward you one complete turn. Bring bobbin thread up by pulling upper thread. THREADING OF TOP THREAD Model 1050 _ _ (_ d_ ® Model1020, 1030, 1040, 1045 (_/ ® TOP TENSION CONTROL Model 1050 Model1020, 1030, 1040, 1045 Probably the most important control on your machine is this one that regulates your top thread tension. It consists of discs between which the thread passes. The pressure on these ...
Otros modelos de este manual:Máquinas de coser - 1030 (2.66 mb)
Máquinas de coser - 1040 (2.66 mb)
Máquinas de coser - 1045 (2.66 mb)
Máquinas de coser - 1050 (2.66 mb)