Votos - 1, Puntuación media: 4
(
)
)
|
Resumen del manual
Open hinged latch of position and open the bobbin case and pull bob shuttle race cover. bin case out of machine. th htf’h k,-k bin will fall out easily. INSERTING BOBBIN INTO BOBBIN CASE 1. Pull off 5cm of thread 2. Guide the end of thread from bobbin and insert it into slot. into bobbin case as shown. J J Tension spring 3. Pull Into slot and under 10cm tension spring and draw out about 10 cm of thread. —7— INSERTING BOBBIN CASE INTO SHUTTLE RACE 7, 1. Raise needle to its highest position, pulling thread to the front, open the latch of bobbin case and hold it. nsert 2. Holding latch open, place bobbin case onto centre pin in shuttle and release latch —8— DRAWING UP BOBBIN THREAD 1 Hold upper thread with left hand, turn the hand wheel slowly towards you until the needle goes down and comes up. Then stop the hand wheel when the takeup lever is at its highest position. Lightly draw up the upper thread will be brought up in a loop. 2. Pull out both threads and presser foot machine. to the rear of CHANGING SEWING DIRECTIONS 1. Lower needle down into fabric and 2. Put down presser foot and raise presser foot, pivot the fabric start to sew. around the needle to change direction as desired. —10— MACHINE LEVELING DOWN up —11— ADJUSTING THREAD TENSION Correct Fabric Upper thread Weak Strong Bobbin thread Upper thread tension may be adjusted by turning the thread tension dial. . Inside of fabric Upper thread Lower thread tension can be adjusted by turning screw on bobbin case slightly to the right (clock-wise) to increase tension. (Anti-clockwise) to the left to decrease tension. —12— REGULATING THE PRESSER FOOT PRESSURE set lever at 1, set at lever for desired pressure, for tight fabrics 1. Push down ind3Iorheavy fabrics 2 for mediumfjb1 poor feeding, skipped stitches, or- -difficulty cause 2. Insufficient pressure may in guiding the fabric. When darning or sewing freehand embroidery release the pressure by setting 3. the lever on 0. DROP FEED ‘, , 4’ 1’— Push feed lever down to drop feed below needle plate for darning, A embroidery, and button sewing. for normal ab6ve needle plate B. Push feed lever up to raise feed sewing. —13 — CHANGING NEEDLE Flat face side away from you. 1. Raise needle to its highest position. 2. Loosen neeaie clamp screw and remove old needle. 3. With the flat side of the needle facing away from you, insert needle as far up as it will go. 4, Tighten the needle clamp screw securely. —14— FABRIC •THREAD NEEDLE TABLE Please note that th foliowng list is a guide when sewing different fabrics. essureof F a hr c Thread Needle 00t hIeg Light Tricot bOS Fiberj ‘ — 13 14 Si k SOsi7:j iL 50S.Fiber Wool silk Silk 6080 ii14 Ging ham Cotton — 0.5 305 4 rhin Jerse’ 60 S. Fibei 11 50 Silk Gabardine 50 cotton 1416 Heavy Denim — 0.5 3 0.5 Jersey SOS. Fiber 1 1 -14 — fl Twd5014 — 15— -.Jc) (31 L) - Cl) m < 2 I LI I IlI — -o -- —r ———— -1 //A\V/A\\ -a -4 m 11 h;i4 VVV J]’ 2 C’, m I m C, -I 0 2 0 -o m > 0 IJ*±±-4 2 ‘ rw m iI -4 -.— —- —— — —-. —.- —- - TO START SEWING Important Hints. 1. Raise the takeup lever to its highest position when starting and stopping sewing. 2. Hold both threads about 10 cms to the rear of machine for the first two to three stitches. 3. Sufficient fabric should be placed under needle before lowering presser foot. 4. Depress foot/Speed control and start to sew, 5. Test the machine stitches on a scrap of fabric you plan to use, adjusti...
Otros modelos de este manual:Máquinas de coser - 1515 (650.87 kb)
Máquinas de coser - 1525 (650.87 kb)
Máquinas de coser - 1525 (650.87 kb)