Votos - 4, Puntuación media: 3.5
(
)
)
|
Resumen del manual
catches. large screw driver to make 4. Push the needle up as far as it will go. certain the foot is secure. 2. With your thumb and index finger, 5. Tighten the needle clamp screw firmly gently snap in. with the large screwdriver from your accessory box. SECTION 2. PREPARE YOUR MACHINE FOR SEWING > Your choice of needle and thread depends on the fabric you are sewing. In your needle envelope, you will find the following color-coded needles: Blue (11 ) ......... for stretch fabrics. Orange (11 ) ........ for lightweight fabrics. Red (14) .......... for medium or medium-heavy weight fabrics. Purple (16) ........ for medium-heavy weight fabrics and decorative topstitching on these fabrics. (This needle has a larger thread hole for thicker topstitching ttm_d._ Green|_ ...,:,.. for _ _ fa_r_ decorative top-stitching on these fabrics. Replacement Kenmore needles are avialable at your nearest Sears stores. • Check Your Needle 1. Look for barbed or blunt point. 2. A damaged needle can cause permanent snags or runs in knits, fine silks and silk-like fabrics. Always buy a good quality thread, It should resist tangling and be strong, smooth and consistent in thickness, • Fabric, Needle, Thread FABRIC Lightweight: Batiste, Dimity, Chiffon, Silks, Fine Lace, Organza, Crepe, Taffeta, Voile, Organdy Medium Weight: Cotton, Cotton Blends, Percale, Gingham, Shantung, Pique, Seersucker, Satin, Knits, Vinyl Suitings, Linen, Wool Crepe, Leather Medium Heavy Weight: Corduroy, Denim, Wool, Sailcloth, Wool Flannel, Gabardine, Velvets, Leather Heavy Weight: Coatings, Upholstery Cotton Duck, Heavy Twills, Canvas on a.ttyp_of fabric Stretch Fabric: Polyester Double Knits, Nylon Tricot, Jersey, Stretch Terry, Spandex, Cire Tricot and Stitch Length NEEDLE SIZE AND COLOR 11-ORANGE 14-RED 14-RED or 16-PURPLE 1B-GREEN r, , TS_GREEN 11-BLUE (STRETCH FABRIC NEEDLE) Chart THREAD SIZE Polyester Core/Cotton Wrap Fine Mercerized Cotton Silk A 50 Mercerized Cotton Polyester Core/Cotton Wrap Silk A 50 Mercerized Cotton Mercerized Heavy-Duty Polyester Core/Cotton Wrap Silk A Heavy Duty Mercerized Cotton Polyester Core/Cotton Wrap Silk A (_ aS top thread only) Polyester Core/Cotton Wrap 50 Mercerized Cotton RECOMMENDED STITCH LENGTH SETTING 2 (12 stitches per inch ) 2--2.5 (10-12 stitches per inch) 2--3 (8-I0 stitches per inch) 3 (8 stitches per inch ) t°°per inch)_ 2--2.5 (10-12 stitches per inch) SECTION 2. PREPARE YOUR MACHINE FOR SEWING Prepare the Bobbin • To Remove the Bobbin Casefrom the Machine • Wind the Bobbin J clutch knob inside the hand wheel J Remove the extension table from the machine by pulling it to the left. Open the shuttle cover by pulling down the embossed part on the left side of the cover. To remove bobbin tle, pul! open latch Pull bobbin case shuttle. case from shut- of bobbin case. straight out of toward moving bobbin. you to while stop the needle you winding from the Raise needle to its hi_ghest position by rotating hand wheel toward you. SECTION 2. PREPARE Y_OUR MACHINE FOR SEWING Wind the Bobbin (Continued) 7 Draw thread from spool through Pull end of thread through hole in Place bobbin onto bobbin winding Wind thread until winder stops. bobbin winding tension disc asshown. bobbin asshown. spindle with end of thread coming Push bobbin winding spindle to the from the top of the bobbin. Push left and clip thread. Remove bobbin. bobbin winding spindle to the right Turn clutch knob away from you until it clicks. Holding onto end of while holding hand wheel for normal thread, start machine. When bobbin is sewing operation. slightly filled, snip off end of thread. • Insert the Bobbin into the Bobbin Case Place bobbin in bobbin case Pull thread through slot of case Pull thread under tension Holding latch open, position Case should lock into place making sure thread feeds clock-as shown. spring and through the opening case into shuttle and release when latch is released. wise and is coming from as shown above. Pull 3 to 4 latch. bobbin as shown. inches of thread from bobbin. SECTION 2. PREPARE YOUR MACHINE FOR SEWING Prepare Your Top Thread • Thread Your Needle I .... J I _J i _ ,, _.. • Raise take-up lever to its highest position Raise presser foot]ever. Place spool on spool pin as shown, with by turning hand wheel thread coming from the toward you. back of the spool. 1. Draw thread into thread guide using both hands. The numbered steps above follow on the illustrations. Dotted lines show places where loops and then is pulled tight. the numbers the thread 2. While holding thread near spool, draw thread down into the tension check spring holder. 3. Firmly draw thread up and through take-up lever from right to left. 4. Draw thread down and slip it into needle bar thread guide. 5. Thread needle from front to back. NOTE: You may want to cut the end of thread with sharp scissors for easier area and then around needle threading. the 10' SECTION 2. PREPARE YOUR MACHINE FOR SEWING Pick Up Your Bobbin Thread Raise presser foot lever. Ho...
Otros modelos de este manual:Máquinas de coser - KENMORE 12581 (2.81 mb)
Máquinas de coser - KENMORE 12781 (2.81 mb)
Máquinas de coser - KENMORE 12681 (2.81 mb)