Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
Operating the machine without the foot pedal 1. Lift the needle (R) above the presser foot (F) by turning the had wheel (K) slightly in clockwise direction (away from you.) 2. Raise the presser foot (F) by lifting up on the rear at the machine above the Presser foot bar. 3. Position fabric to be sewn under the presser foot (F) with presser foot (F) in raised position. Make certain seam direction is toward you, aligned with the presser foot (F), with seam location directly under the needle (R). 4. Lower the presser foot (F) by releasing the presser foot lever (G) downward. 5. Rotate the hand wheel (K) in a clockwise direction two full turns to lock and start seam. Stop. 6. Select speed by pressing speed button (L) on face of machine. High speed, button is extended out. Low speed, button is in, flush with machine. Use low speed for intricate work, which requires a lot of stopping, starting and turning fabric. Use high speed for long uninterrupted seams. 7. Turn power switch (A) to “ON” position. 8. Gently guide the fabric to keep the seam straight by pressing it lightly down with your fingertips on both sides as it feeds through the presser foot (F). 9. When the seam is finished, turn switch (A) to off. 10.Raise the needle (R) above the fabric by turning the hand wheel (K) slightly in a clockwise direction. 11.Raise the presser foot (F) by lifting the presser foot lever (G). 12.Pull fabric toward you leaving about 5-10 inches of thread between the fabric and the machine. 13.Cut thread close to fabric, leaving excess thread loosely lying on the sewing deck in the direction of the presser foot (F) and toward you. 14.Begin the next seam in the same manner as above by following operating steps above. To use the with foot pedal (Follow steps 1-14 with these exceptions) 1. Make certain machine is in “OFF” position. 2. Plug the foot pedal jack(M) into back of machine. 3. Turn machine on by pressing the foot pedal. 4. Press gently on the foot Pedal to run the machine. Let up to stop. When you are finished sewing a seam, ease your foot up and off of the foot pedal. Note: The on-off switch on the machine should be in the “OFF” position when using the foot pedal. 8 Operating the Sew E-Z Adjusting thread tension Tension for maximum performance has been set and adjusted at the factory. However, if you should find that stitches are too loose, or too tight, you can adjust the stitch. 1. Loosen stitch by turning the tension screw (Q) counter-clockwise. 2. Tighten the stitch by turning tension screw (Q) clockwise. Sewing heavier fabric may require loosening the stitch. Very light fabric may require tightening the stitch. 3. Bobbin tension cannot be adjusted. Stitch length adjustment You can use the stitch length adjustment button control to change the stitch length in sewing. 1. Push the button to the left in order to get the longest stitch length. This is recommended for normal sewing. 2. By turning the button towards the right hand side, the stitch length will be reduced. 3. When the button is set to the middle point, the stich length will become zero, therefore, the fabric will not move forward. Reverse sewing Push and hold the lever down to sew in reverse. Sewing Sleeves The machine designed to allow you to sew sleeves easier. 1. Lift up the presser foot (F) and position the sleeve under the needle. Put the bobbin part of the sleeve in the gap between the platform and the base. 2. Lower the presser foot and follow the step 5-13 in the section of operating the machine on the previous page. Now you can sew the sleeve easily. 9 Changing the Needle 1. Turn the handwheel (K) clockwise to raise the needle (R) to its highest position. 2. Loosen the needle clamp screw (O) by turning it counter-clockwise (toward you). You may need to use a short slotted screwdriver or small pliers. 3. Remove the needle (R) pulling down, away from the needle clamp(P). 4. Place the new needle with the flat side facing in against the needle clamp(P). 5. Push it gently as far up as it will go, and against the needle clamp(P). 6. Tighten the needle clamp screw (O) while holding the needle (R) in place. Note: Size 90/14 sewing machine needles are recommended. 10 Precautions Set the POWER switch to OFF and don’t touch the switch when inserting batteries or plugging in or replacing the needle. Keep the unit away from children. If operated by a child, an adult shall watch the operation. Set the switch to OFF after usage and remove the batteries or pull off the plug. Don’t mix old batteries with new ones. Don’t dismantle or rebuild the unit. Don’t switch on when fabric has not been put on the unit even though top and bottom threads are ready. Troubleshooting 1. The sewing machine does not run when the power switch is pressed. •Batteries are inserted incorrectly. Insert the batteries again using the diagram provided inside the battery compartment. •Batteries are exhausted. Replace with new batteries. •Make sure the Adapter (6V,1.2A) and foot controller are c...
Otros modelos de este manual:Máquinas de coser - SEW E-Z W338 (395.37 kb)