Votos - 1, Puntuación media: 5
(
)
)
|
Resumen del manual
The higher the number, the thicker the needle. A STRETCH needle isstretch needle recommended for stretch fabrics. * Do not use any needle which is bent or blunted. 5 REMOVING AND ATTACHING THE PRESSER FOOT To Remove: 1. Turn the balance wheel towards you until the needle is at its highest position 2. By lifting the lever on the back of the foot holder, the presser foot will drop off. Note: *Do not force the presser foot to remove it. To Attach: 1. Place the presser foot so that the pin on the foot lies just under the groove of the foot holder. Lower the foot holder. ,2. When the presser foot lifter is raised youll fin d the presser foot is locked in place. REGULATING THE THREAD TENSION Generally, should any tension adjustment be necessary, the adjustment can normally be made by regulating the upper thread tension dial only. Bobbin thread tension has been adjusted at the factory and readjustment is seldom required except for special instances, thread and fabric. Bobbin thread tension is just right when you can pull the thread from bobbin case easily with a little resistance. Thread tension may be adjusted by tightening or loosening the thread tension dial. The needle thread and the bobbin thread Remember the higher the number, the tighter the tension. Correctly balanced tensions for one fabric may not be suitable for another. The required tension depends upon the stiffness of fabric, thickness of the fabric, numbers of layers of fabric being sewn, as well as the type of stitch you are making. It is better to test the stitching on a scrap of the fabric you are using before starting to make a garment. The general range for many fabrics is 3-5. REGULATING THE THREAD TENSION Generally, should any tension adjustment be necessary, the adjustment can normally be made by regulating the upper thread tension dial only. Bobbin thread tension has been adjusted at the factory and readjustment is seldom required except for special instances, thread and fabric. Bobbin thread tension is just right when you can pull the thread from bobbin case easily with a little resistance. Thread tension may be adjusted by tightening or loosening the thread tension dial. The needle thread and the bobbin thread Remember the higher the number, the tighter the tension. Correctly balanced tensions for one fabric may not be suitable for another. The required tension depends upon the stiffness of fabric, thickness of the fabric, numbers of layers of fabric being sewn, as well as the type of stitch you are making. It is better to test the stitching on a scrap of the fabric you are using before starting to make a garment. The general range for many fabrics is 3-5. 6 STITCH LENGTH DIAL (Model 377 and 374 only) To change the length of the stitches proceed as follows: Turn the dial so that the number for the required stitch length is at setting mark. The numbers indicate the approximate stitch length in mm. The smaller the numbers, the shorter the stitch. English Model 377 Model 374 settingmark stitch lengths REVERSE STITCH: (Model EP 377/374/373/372) Press center of the stitch length dial (reversing button) and hold for reverse stitching. Fabric will immediately start feeding backwards. Release button and machine will resume normal forward sewing. Very useful for fastening ends of seams and darts without having to tie threads, and for strengthening seams. Model EP 377 Model 374 Model 373/372 THE PATTERN SELECTOR(Model 377) patterns shown on the panel respectively, as follows; M( ) straight stitch, middle needle position O( ) straight stitch, left needle position 1-5( 54321) zigzag stitch with variable width A( ) tricot stitch B( ) stretch blind stitch C( ) double action stitch D( ) reverse blind stitch automatic buttonhole sewing the SS mark is uppermost. This is a standard adjustment for most types of fabric. For different types of fabric, adjustment may be necessary. To shorten the stretch stitches, turn the dial slightly towards To lengthen, turn the dial towards . On most fabrics, these adjustments allow for various pattern possibilities. When making stretch stitches, the mark must always be within the SS range - (see drawing). .°.± Selecting Stretch Stitch: When sewing stretch stitch, set the stitch length dial at S.S. . When you release the engagement on the dial, the stretch stitch mechanism will be off automatically. M( ) triple straight stretch stitch, middle needle position. O( ) triple straight stretch stitch, left needle position. 1-5( 54321) triple zigzag stretch stitch or ric-rac stitch C( ) double overlock stitch A( ) smocking stitch B( ) fancy stretch stitch or blanket stitch D( ) overlock stitch .°.± .°.± The desired pattern can be selected by turning the pattern selector dial. The marks on the dial correspond to the Standard djustment Turn the stitch length dial so that SS SS 7 E ( ) stretch blind stitch F ( ) double action stitch G ( ) reverse blind stitch automatic buttonhole sewing THE PATTERN SELECTOR ( Model 373/372) straight...
Otros modelos de este manual:Máquinas de coser - 372 (4.32 mb)
Máquinas de coser - 374 (4.32 mb)
Máquinas de coser - 377 (4.32 mb)