Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
It has advantages of light weight,simple appearance and easy to adjust speed besides all features of CZD series. I. Uses and characteristics. 1 .It is suitable for cutting various kinds of cloth,sponge and leather. 2.1t is easy to operate. 3.The contacting parts of driving pulley and band knife are made of wear-resisting material, and thus resulting long service life and low noises. 4.Driving pulley adopts large diameter(o 300mm) design to protect band knife from being broken. 5.stepless speed adjusting by converter,it is easy to change cutting speed. 6.The product adopts cushion system,and the material can be moved smoothly and flexibly in cutting operation. II.Description of all parts.(Fig.1,2,3) KoMnaHMA „KpyHr" Ten./^aKc: (495) 989-22-97 No. D escription 1 machine frame 2 long guard pipe 3 lower guard 4 short guard pipe 5 digital keypad 6 switch box 7 height adjusting screw 8 machine support mounting pad 9 movable roller 10 front cover 11 machine support 12 metal plate of table 13 metal plate with holes 14 table support 15 cutting table 16 guide block 17 grinding wheel device 18 upper guard 19 tension bar 20 tension box 21 converter 22 main motor 23 band knife 24 blower 25 driving wheel Fig. 2 — 2 — KoMnaHMA „KpyHr" Ten./^aKc: (495) 989-22-97 III. Installation.(Fig.4,5) 1. Align holes in table (3-1) with nuts (3-2) on machine support,then retighten screws (3-3) to lock nuts. 2. Loosen nut (9-2),turn screw 9 to set the table to required height Then retighten nut. 3. Loosen nut (4-2),turn screw 4-1 of table support until the table rest on the support bar.Then retighten nut (4-2). Fig. 4 Fig. 5 IV. Operation. 1. Depends on thickness of materials,rotate rotary button to adjust guide block and protection device to the lowest position(Fig.6). 2. Turn on the band knife and blower with switches in boxes located at the right side beneath the table on. 3. Press down the material to cut with hands,and make it contact with band knife.Move the material all around to achieve the desired forms. Rolling knob nit r Guide block /Roiling knob C /^Safety fitting 1/e Cutting table Z Fig. 6 3 — KoMnaHMfl „KpyHr" Ten./^aKc: (495) 989-22-97 Notice: 1. Take care of the band knife in operation. 2. Do preparing for the next cutting process only with the machine turner off. V. Grinding. 1. Grinding the knife when the knife becomes dull and the blade is dirty 2. As shown in Fig.7,pull the grinder lever to start grinding. 3. If the grinding wheel is unable to reach the band knife after pulling the grinder lever,then loosen the nut,and turn the wing screw to make the mat (J) move forward a little way (Fig.8). Notice: Only a little way should be moved,or the band knife will be pressed by the grinding wheel,it is impossible to grind the knife. 4. If the blade is ground unevenly as shown in Fig.9, then adjust the two grinding wheels left or right by turning the two knurled screws(7-6) shown in Fig.10.The arrows in Fig.9 indicate the moving direction of the grinding wheels. Fig. 7 X L J (i) fi _J(2) Rights Left Left«- O Right Fig.9 Fig. 10 — 4 — KoMnaHMA „KpyHr" Ten./^aKc: (495) 989-22-97 5. Generally,the angle between two blades should be small for thin materials,and the angle should be big for heavy materials.Refer to Fig. 10 for details.and the small arrow indicates the moving direction of two grinding wheels. 1.5-2mm . .1 1 0,7mm Standard t! 3 1 For thin fabrics For thick fabrics Standard For thin fabrics Standard For thick fabrics Fig. 11 6. The worn grinding wheels can be used continuously by moving them closely. 7. If the knife is not ground though the grinding wheels has been adjusted correctly .The gringding wheels are worn out and should be replaced.Loosen nuts shown in Fig. 10 to replace. VI. Replacement of the band knife. 1. The knife should be replaced when the width of the knife is reduced to smaller than 5 mm by several times ground. 2. Remove two round guard covers 17 and 18 (Fig. 12) on the machine frame. 3. Remove front cover,guide block and protection device of the grinding device. 4. Loosen the wing nut beneath the machine table to pull out strip plate 13. 5. Rotate the tension bar 19 (Fig.2) to make the band knife loose for replacing. — 5 — Компания „Крунг" тел./факс: (495) 989-22-97 — 6 KoMnaHMA „KpyHr" Ten./^aKc: (495) 989-22-97 VII. LC-A05E/LC-A1OE Digital keypad operation 1.Description and Function of the Digital Keypad When delivered from the factory ,the digtal keypad module is mounted on the front panel of the AC drive.This module has two parts:a display panel and a keypad.The display panel allows the user to program the AC drive,as well as view the different operating parameters.The keypad is the user interface to the AC motor drive.Refer to the following figure for a description of the d...