Votos - 3, Puntuación media: 4
(
)
)
|
Fotos y especificaciones Juki HZL-F600 |
Resumen del manual
Place the fabric under the presser foot, align the marking with the sewing-start point. Penetrate the needle into the fabric by turning the hand wheel and lower the presser foot. Start sewing. t Start from here The machine will stop automatically after sewing the buttonhole. * If a buttonhole of the same size will be sewn again, push the thread trimming button to trim the threads and raise the presser foot. Under this condition move to another point, lower the presser foot and then start sewing. * Do not change stitch length and/or zigzag width during buttonholing. Otherwise this will cause imbalanced stitches. * If thread trimming button is pushed while sewing buttonhole, the machine will stop and will not complete the buttonhole. * Depending on material to be sewn and weaving direction of the material, there might be a slight difference in zigzag widths between right and left lines of buttonholes. Test sewing is recommended. 46 6 Unplug the sensor pin after sewing. Ripper Opening the buttonhole using a ripper. [double bartack] Pierce a stopper pin at the bartack and open the buttonhole with a ripper. Be careful not to cut the stitches. [Keyhole buttonhole] Place a cardboard under the buttonhole and make a hole with the eyelet punch. Then pierce a stopper pin at the bartack and open the buttonhole with a ripper. Buttonhole clamping plate Clamping plate A Caution Turn off the power when setting the clamping plate. It will be easier to sew buttonholes on the thin fabrics and/or near the overlapped sections, if the clamping plate is used. 1. Attach the buttonhole presser foot to the presser foot holder, with the clamping plate together. 2. Place the fabric between the presser foot and the clamping piate. * You can remove the clamping plate by holding ©. V_ 47 ■ Buttonhole with gimp UJ S3 * ABC nor CP r» Œj01 Pattern No. Presser foot Direct 0 Buttonhole presser foot (E) A Attention Turn off the power before replacing the presser foot. Buttonholes with gimp thread prevent the buttonholes from stretching and can make them more secure. Use thread such as hand-sewn buttonholes and similar for gimp thread. -LI—1-r ■ _Jts-jdds'oi- j— jfooft n -—|—J "j±r; 1 i 3 5 6 Pass the needle thread through under the presser foot and then draw the thread to the side of the presser foot. Put one end of gimp thread into the notch at the front right side of buttonhole presser foot, pull the gimp thread under the presser foot and thread it at the hook of the presser foot. After threading at the hook, pull the gimp thread back under the presser foot and put it into the notch at the front left side of the presser foot firmly. Bring down the needle to the sewing start point and lower the presser foot. Sew the buttonhole. Pull the left gimp thread to take off slack and cut excess gimp thread. 48 When changing the width of the buttonhole Turn the zigzag width adjusting dial/button. Turn to the left Pushing //áN ~W+ ( F4001 F300 ) The width becomes narrow * The setting of the buttonhole width and stitch length will be cancelled when the power is shut down or another pattern is selected. Turn to the right The width becomes wide When changing the density of the seam Turn the stitch length adjusting dial/button. Turn to the left Pushing GnüsSÏ® (F400/F300 ) 6 Ci Narrow stitches Large stitch Turn to the right Pushing * The stitch length becomes narrow narrow The stitch length becomes larger arger The width of buttonhole can be changed by ( (□¿o)) option. (Refer to page 80) 49 { Manual 2-step buttonhole * ABC n 0 T£) p* 123 illlillljlllilllEIIIS I I llllllliliiiifEillilli Pattern No. Presser foot Buttonhole 03 Manual buttonhole presser foot (I) A Attention Turn off the power before replacing the presser foot. * Turn the “zigzag width” and “stitch length“ adjusting dials before sewing when you want to change the buttonhole width and density of the seam. Î Set the manual buttonhole presser foot (I). 3 Pass the needle thread through the hole of the presser foot and pull it out sideways together. Bring down the needle on the sewing start point and lower the presser foot. Push start/stop button to sew. * At this time, if the start/stop button is pushed, the machine will stop sewing. And if the start/stop button is pushed again, then the machine will continue to sew the left side of the buttonhole. Push the reverse stitch button when it reaches the necessary length of the left side of the buttonhole. Sew bartack and the right side of the buttonhole, then the machine sews bartack and right side of the buttonhole. 50 Sewing start point ^ Sew bartack and lock stitches until the machine stops automatically. 7 Pierce a stopper pin at the bartack and open the buttonhole with a ripper. Be careful not to cut the stitches. As the numbers of stitches of both right and left lines of buttonhole is memorized in the sewing machine, the buttonhole o...
Otros modelos de este manual:Máquinas de coser - HZL-F300 (5.2 mb)