Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
Press the “ “ button again to leave the memory mode and return to Direct mode. Please Note: The Direct mode patterns and buttonholes cannot be programmed or put into memory. Press this button when the incorrect character is selected. Each press of this button erases one character. Or press this button to remove an added pattern when sewing combinations of characters or decorative stitches. Press the arrow buttons “ “ or “ “, in memory mode, to check the combination programmed in the memory. USEFUL SKILLS USEFUL SKILLS Sewing corners Reverse Free arm 1. Stop the sewing machine when you reach a corner. 2. Lower the needle into the fabric with the hand wheel or by pressing the needle up/ down button once. 3. Raise the presser foot. 4. Use the needle as a pivot and turn the fabric. 5. Lower the presser foot and resume sewing. Reverse stitching is used to secure the threads at the beginning and at the end of a seam. Press the reverse button and sew 4-5 stitches. The machine will sew forward when the button is released. Free arm sewing is convenient for sewing tubular areas such as pant hems and cuffs. 36 Sewing on heavy fabric Cardboard or thick fabric The black button on the right side of the presser foot will lock the presser foot in a horizontal position if you push it in before lowering the presser foot. This ensures even feeding at the beginning of a seam and helps when sewing multiple layers of fabric such as sewing over seams when hemming jeans. When you reach the point of an increased thickness, lower the needle and raise the presser foot. Press the toe of the foot and push in the black button, then lower the foot and continue sewing. The black button releases automatically after sewing few stitches. You also can place another piece of fabric with the same thickness at the back of the seam. Or support the presser foot while feeding by hand and sewing toward the folded side. STRAIGHT STITCHES AND NEEDLE POSITION STRAIGHT STITCHES AND NEEDLE POSITION Changing the needle position These setting apply only to patterns 01-05. The pre-set position is “3.5”, center position. When you press the “-“ stitch width adjustment button, the needle position will move to the left. When you press the “+” stitch width adjustment button, the needle position will move to the right. On the LCD screen, the point illustration and the number indicate the needle position. Changing the stitch length To shorten the stitch length, press the “-“ stitch length adjustment button. For a longer stitch length, press the “+” stitch length adjustment button. Generally speaking, the thicker the fabric, thread and needle, the longer the stitch should be. ZIGZAG STITCHES Adjusting the stitch width The maximum zigzag stitch width for zigzag stitching is “7.0”; however, the width can be reduced on any patterns. The width increases as you press the “+” stitch width adjustment button from “0.0-7.0”. Adjusting the stitch length The density of zigzag stitches increase as the setting of stitch length approaches “0.2”. Most zigzag stitches are sewn at “1.0-2.5”. Dense zigzag stitches (close together) are referred to as a satin stitch. 38 Straight stretch stitch Straight stitch Straight stretch stitch Straight stitch STRETCH STITCHES Stretch stitches are strong and fl exible and will give with the fabric without breaking. Suitable for easy to ravel and knit fabrics, as well as joining durable fabric such as denims. These stitches can also be used as decorative top stitches. Straight stretch stitch is used to add triple reinforcement to stretch and stressed seams. Triple zigzag stretch stitch is suitable for firm fabrics like denim, poplin, duck, etc. OVERCASTING STITCHES OVERCASTING STITCHES Using the overcasting foot 1. Change the presser foot to the overcasting foot (E). 2. Sew the fabric with the fabric edge against the guide of the overcasting foot. Attention: The overcasting foot should be used to sew with patterns and only. Do not set the stitch width narrower than “5.0”. It is possible for the needle to hit the presser foot and break when sewing other patterns or using another width. Using the standard foot 1. Change the presser foot to the standard foot (T) . 2. Overcast along the edge of the fabric so that the needle drops over the edge of the fabric on the right side. 40 BLINDHEM : Blindhem for woven fabrics : Blindhem for stretch fabrics Please Note: It takes practice to sew blindhems. Always make a sewing test first. 5mm 5mm Snap on foot F. 1. Fold the fabric as illustrated with the wrong side up. Wrong Overcasting Wrong side side stitches 2. Place the fabric under the foot. Turn the handwheel forwards by hand until the needle swings fully to the left. It should just pierce the fold of the fabric. If it does not, adjust the stitch width accordingly. 3. Adjust the guide on the foot (b) by turning the knob (a) so that the guide just rests against the fold. 4. Sew slowly, guiding the fabric carefully along the edge of the guide. 5. Turn fabric ...
Otros modelos de este manual:Máquinas de coser - HUSKYSTAN C10 (3.85 mb)