Votos - 1, Puntuación media: 5 ( )

Fabricar: Brother Tamaño del archivo: 1.58 mb Nombre del archivo: Idioma del manual:

When connecting the foot controller, be sure to turn off the sewing machine in order to prevent the machine from accidentally being started. When you press the foot controller down lightly, the machine will run at a low speed. When you press harder, the machine’s speed will increase. When you take your foot off the foot controller, the machine will stop. Slower Faster You should make sure that nothing is placed on the foot controller when the machine is not in use. CAUTION . Do not allow pieces of cloth and dust to build up on the foot controller. Doing so could cause a fire or an electric shock. Note . When the foot controller is plugged in, the start/stop button cannot be used to start sewing (only for models equipped with the start/stop button). Slide the sewing speed controller to the left or a right to select the desired sewing speed. Slide the sewing speed controller to the left to sew at a slower speed, or slide the speed controller to the right to sew at a faster speed. a Sewing speed controller • The speed set using the sewing speed controller is the foot controller’s maximum sewing speed. Changing the needle stop position Normally, the sewing machine is set to leave the needle in the fabric when sewing is stopped. Instead, the machine can be set to leave the needle raised when sewing is stopped. Turn off the sewing machine. a b Hold down the “–” side of (stitch selection key) on the left and turn on the sewing machine. After turning on the sewing machine, release the “–” side of (stitch selection key). • The needle stop position changes to the raised position. Memo . Perform the same operation to change the needle stop position to the lowered position. Changing the initial needle position Normally, the straight stitch (left needle position) is automatically selected when the sewing machine is turned on. The machine can be set so that the straight stitch (center needle position) is automatically selected when it is turned on. Turn off the sewing machine. a b Hold down the “+” side of (stitch selection key) on the left and turn on the sewing machine. After turning on the sewing machine, release the “+” side of (stitch selection key). • The initial needle position changes to the center needle position. Memo . The specified initial needle position is maintained even after the machine is turned off. . Perform the same operation to change the initial needle position to the left needle position. Cancelling the operation beep (for models equipped with the operation beep) When the sewing machine is purchased, it is set to beep each time a key is pressed. This setting can be changed so that the machine does not beep. Turn off the sewing machine. a b Hold down the “–” side of (stitch width adjustment key) and turn on the sewing machine. After turning on the sewing machine, release the “-” side of (stitch width adjustment key). • The machine is now set so that it will not beep. 1 11 KNOWING YOUR SEWING MACHINE THREADING THE MACHINE Winding the bobbin KNOWING YOUR SEWING MACHINE THREADING THE MACHINE Winding the bobbin This section describes how to wind the thread onto the bobbin. • For details on the fast bobbin winding, see page 14. 1Pulling it in as far as possible. a Pre-tension disk b Bobbin winder shaft c Bobbin CAUTION . Only use bobbins (part code: SA156, SFB) that have been designed for this sewing machine. Using other bobbins may cause damage to the machine. . We designed the bobbin that comes with this machine. If you use bobbins from other models, the machine will not work properly. Only use the bobbin that comes with this machine or bobbins of the same type (part code: SA156, SFB). Actual size 11.5 mm (7/16 inch) This model Other models Pull up the spool pin as far as possible, and a then put a spool of thread on this pin. b Pass the thread around the pre-tension disk. CAUTION . If the spool of thread is not in the right place, the thread may tangle on the spool pin. Pass the end of the thread through the hole on the bobbin from the inside of the bobbin. d Put the bobbin onto the bobbin winder shaft and slide the bobbin winder shaft to the right. Turn the bobbin clockwise, by hand, until the spring on the shaft slides into the groove of the bobbin. 12 a Spring on the shaft b Groove of the bobbin Turn on the sewing machine. e f While holding the end of the thread, gently press the foot controller or press (start/ stop button) (for models equipped with the start/stop button) to wind the thread around the bobbin a few times. Then stop the machine. Note . If the sewing machine is to be operated using the foot controller, connect the foot controller before turning on the machine. . When the foot controller is plugged in, the start/stop button cannot be used to start sewing (only for models equipped with the start/stop button). Trim the excess thread above the bobbin. g CAUTION . Make sure you follow the instructions carefully. If you do not cut the thread completely, and the bobbin is wound, when the t...

Descargar ahora

Introduzca dos números de la imagen: