Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
(Refer to page 99.) 84 Part IV Sequencer CYCLE RECORD This mode allows you to have specified recording measures continuously repeated. Thus you can record measures by adding notes during any cycle. 1.0n the REALTIME RECORD display, specify “REC” for a track number you are going to record, and “PLAY” fortrack numbers you wish to have played back. 2. Press the CYCLE: OFF button. • The display looks similar to the following. 6. Play the keyboard. • The specified measures are repeated, during which time you can record by adding notes little by little at the correct timing (over-dubbing). • If you wish to erase all the performance data from the specified measures, press the CLEAR button. • If CYCLE is selected and the v button used to select OFF, cycle recording is not activated. This button does not work during recording. • To return to the REALTIME RECORD display, press the EXIT button. • Cycle record can also be started from the REALTIME RECORD display whenever the CYCLE: ON indication is shown. 7. When you have finished recording, turn off the PROGRAM MENUS button. ||f]RERLTII1E RECORD CURRENT MEASURE : 1 CYCLE : ON i CVCLE START MEASURE : 1 i CVCLE END MEASURE 1 3. Select CYCLE START MEASURE, and use the VALUE a and v buttons to specify the beginning measure number. 4. Select CYCLE END MEASURE, and use the VALUE a and v buttons to specify the ending measure number. • The measure in which the END command has been stored can also be specified. START END t_l CYCLE END MEASURE: 4 5. Press the START/STOP button. • If the metronome is on, cycle recording of the specified measures begins after a two-measure count. 85 Sequencer Sequencer Part IV Sequencer Sequencer Play Play back your recorded performance. 1. Press the SEQUENCER PLAY button to turn it on. The display looks similar to the following. |§ SEQUENCER PLAY DEB SONG l: MEAS <& MEASURE = 1 TIME SIG. = 4/4 MEDLEV ► 4 MIXER J= 82 IdftVJ IJT:VJ l^:VJ IÜWÏ71 -* 2. Use the SONG button to select the song number you wish to play back. 7. Press the START/STOP button. • The recorded performance is played back from the specified measure. • When playback is begun from a measure in which an INTRO, COUNT INTRO, FILL IN or ENDING is recorded, the corresponding function does not work. • You can press the MIXER button and modify the settings for each part. 8. To stop playback, press the START/STOP button. • If the START/STOP button is pressed again, playback will continue from the point it was interrupted. 9. When you are finished playing back your performance, press the SEQUENCER PLAY button to turn it off. If “PLAY” is specified for the track to which the RHYTHM (RHY) part is assigned, the MEASURE display used in the STEP RECORD and EDIT displays is shown conforming to the time signature data stored in the RHYTHM part. 3. Use the balance buttons below the display to show “PLAY” above the track numbers you wish to have played back. • Highlighted track numbers indicate tracks that are already recorded. • Use the upper buttons to select tracks 1 to 8, and the lower buttons to select tracks 9 to 16. • You can select two or more tracks to play back at one time. 4. Use the TEMPO/PROGRAM dial to adjust the playback tempo. • The tempo is shown on the display as “J =”. 5. Press the SEQUENCER RESET (FILL IN 1) button. • The SEQUENCER returns to the beginning of the song and the beginning panel settings are recalled. 6. To begin playback from a measure other than measure 1, use the MEAS a and v buttons to specify the beginning measure. • “MEASURE=” indicates the current measure number. Adjusting the playback tempo Even with a song having recorded tempo data, you can use TEMPO/PROGRAM or TAP TEMPO to adjust the tempo to your liking. • When the tempo is changed, all the tempo data of that song is automatically changed by the same ratio. Accordingly, even in song data in which tempo change data is stored, a single adjustment of the tempo produces a natural-sounding playback. • To return to the original tempo, while the song is stopped press the SEQUENCER RESET button. Note that the tempo change is also canceled when you switch to another song or load a new song. • The adjusted tempo is canceled when you begin the recording procedure and the original tempo data will be recorded. 86 Part IV Sequencer CYCLE PLAY You can have specified measures played back repeatedly. I.On the SEQUENCER PLAY display, specify “PLAY” for track numbers you wish to have played back. 2. Press the CYCLE button. • The display looks similar to the following. 6. To stop cycle playback, press the START/STOP button again. • During playback stop, if the SEQUENCER RESET (FILL IN 1) button is pressed, the SEQUENCER returns to the measure number specified in step 3. If the SEQUENCER RESET button is pressed again, the SEQUENCER returns to measure 1. • If CYCLE is selected and the v button is pressed to select OFF, cycle playback is not acti...