Votos - 4, Puntuación media: 3.5
(
)
)
|
Resumen del manual
are indicated on the display. During normal performance, however, the display is off. Data cannot be exchanged through MIDI terminals. • The switch for the COMPUTER terminal is not set to MIDI. Turn off the power to this instrument and set the switch to MIDI. (Refer to page 23.) • Match the channels on the transmitting side and the receiving side. (Refer to page 19.) The sound quavers or is distorted. • When the COMPUTER terminal or both the MIDI IN and OUT terminals are connected to a computer, depending on the computer software the received data may be sent back to the instrument just as it is. Because of this the sound generated from the keys and the sound generated from the returned data are both produced, causing undesirable effects, such as the sounds canceling each other out, for example. In this case, either change the software settings to prevent received data from being returned, or set the MIDI LOCAL CONTROL to off. ■ About the backup memory The selected sound and various functions, MIDI settings and SEQUENCER contents remain in the memory for about one week after the POWER is turned off. • The backup memory will not function until the POWER has been on for about 10 minutes. • If you wish to return all memories and settings to their initialized status, while pressing the MODE SET button, press the INITIAL key on the keyboard. Or you can turn on the POWER while pressing the INITIAL key. • When the POWER is turned on, the MIDI LOCAL CONTROL is set to on. • If you wish to retain the memory for longer than one week, before one week has elapsed, turn on the power and leave it on for about 10 minutes before turning it off again. The settings will remain in the memory for about one week from this time. 24 Assembly Follow the steps below to assemble your Technics piano. Make sure you are using the correct parts and that they are in the correct direction. • At least 2 people are required for assembly. • To disassemble the piano, reverse the procedure. 1. Remove the packing and take the parts out of the carton. Confirm that all the parts on the printed list are present. Brass-colored screw..................4 Black screw (A).... 6 «=■0 Black screw (B).... 4 Clamp...................3 5. Secure the piano body to the stand. List 2. Affix the right and left side planks to the pedal box. (1) Use the 4 brass-colored screws to secure the planks. (2) Be sure to insert the screws straight. • If a screw is inserted crookedly, it may be damaged. (3) Insert each of the 4 screws partway, lightly securing each one little by little. After confirming that the screws are all correctly inserted, tighten each one securely. • If each screw is tightened securely before all the screws are inserted, the last screw may be very difficult to insert. (4) Loosen the pedal cord, stowed on the inner side of the pedal box, and extend it. 3. Affix the rear panel. (1) Insert the 2 black screws (A) partway in the upper part of the rear panel, securing them only lightly. Do not tighten the screws completely at this time. • If the screws are tightened securely at this time, it may be difficult to affix the lower part of the rear panel. (2) Insert the 4 black screws (B) through the mounting holes in the lower part of the rear panel and tighten the screws fully. • Run the screws directly into the pedal box as there are no rough holes in the pedal box. (3) Tighten the 2 black screws (A) in the upper part of the rear panel completely. 4. Place the piano body on the stand WARNING: Avoid pinching your fingers. Note 1 Holding the piano body at least 10 cm in from the edge, place it on the stand so that it does not fall off. Note 2 If the piano body is placed too far to the right or left, or to the front or back, it will become unstable. (1) Insert 2 black screws (A) in the 2 rear screw holes on the underside of the piano body, and turn each screw 5 or 6 times. Push the piano body forward so that the screws are fully inserted in the cutout of the metal piece on either side plank. (This enables you to easily position the piano body on the stand.) (2) Adjust the piano body so that the right and left sides project evenly over the stand. (3) Positioning the piano body on the stand, cbhfirm that the 4 balck screws (A) can easily be inserted. (4) Tighten the 4 screws securely. 6. Connect the pedal cord and power cord to the terminals. (1) Plug the pedal cord and power cord into the terminals on the rear of the piano. (2) Remove the backing from the clamps and affix them as shown in the figure. Secure the pedal cord to the clamps. Confirm: After assembling, check these points. • Are any parts left over? -* Check the assembly procedure again. • Does the piano rattlo when it is rocked? -» Make sure all the screws are securely tightened. • Is the power cord firmly inserted? -♦ Check again. • Is the plug of the pedal cord inserted as far into the connector terminal as it will go? -* If it is not completely ...
Otros modelos de este manual:Sintetizadores / piano - SX-PX332/M (1.06 mb)