Votos - 1, Puntuación media: 4
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
• Are any parts left over? • Review the assembly procedure and correct any errors. • Is the PF-1000 clear of doors and other movable fixtures? • Move the PF-1000 to an appropriate location. • Does the PF-1000 make a rattling noise when you shake it? • Tighten all screws. • Are the pedal and power cords inserted securely into the sockets? • Check the connections. • If the keyboard stand creaks or is otherwise unsteady when you play the keyboard, refer to the assembly diagrams and retighten all screws. CAUTION Be careful not to pinch your fingers. CAUTION Be careful not to pinch your fingers or drop the keyboard. CAUTION Do not hold any part of the keyboard other than four corners as shown in the illustration. Use the front legs as support to raise the stand. Be sure to hold the four corners of the keyboard. Mount the keyboard so that the rubber feet on the bottom of the keyboard fall into the holes on the stand. Attach the cap bolts on the bottom of the stand and tighten them with your hand to fix the keyboard. PEDAL 2 3 2 Connect the pedal cord plug into the PEDAL jack on the left side of the keyboard, with the arrow on the plug facing up. 3 Attach the cord holders in the position shown in the illustration, and clip the pedal cord to the holders. * You can also clip the power cord to the cord holders. 1 Place the pedal unit in front of the rear legs. AC INLET VOLTAGE SELECTOR Troubleshooting Troubleshooting Possible Cause and Solution • The PF-1000 does not turn on; there is no power. Make sure that the PF-1000 has been plugged in properly. Securely insert the female plug into the AC socket on the PF-1000, and the male plug into a proper AC outlet (page 16). • A click or pop is heard when the power is turned on or off. This is normal when electrical current is applied to the instrument. • Noise is heard from the PF-1000’s speakers. Using a mobile phone in close proximity to the PF-1000 may produce interference. To prevent this, turn off the mobile phone, or use it further away from the PF-1000. • The display is too bright or too dark to read. The brightness of the display may be affected by the surrounding temperature; try adjusting the contrast (page 17). • The keyboard volume is low compared to that of the Auto Accompaniment or song playback. The overall keyboard volume or the independent volume level of the keyboard part may be set too low. Raise the MAIN/LAYER/LEFT volume voices or lower the STYLE/SONG volume in the BALANCE display (page 61). • The volume of the Auto Accompaniment or song playback is low compared to that of the keyboard. The volume level of one or more accompaniment parts or song channels is set too low. Raise the part or channel level(s) in the appropriate MIXER display (page 117). • The overall volume is low, or no sound is heard. • The Master Volume is set too low; set it to an appropriate level with the [MASTER VOLUME] dial. • The volume of the individual parts may be set too low. Raise the volume of MAIN, LAYER, LEFT, STYLE, and SONG in the BALANCE display (page 61). • Make sure the desired channel is set to ON (page 61, 76). • Headphones are connected, disabling the speaker output. (This happens when the speaker setting is set to “HEADPHONE SW”; page 138.) Unplug the headphones. • Make sure the speaker setting is set to ON (page 138). • Make sure the Local Control function is set to ON (page 134). • The damper, sostenuto and soft functions do not work for the relevant pedals. Each pedal has been assigned to a different function. Make sure that each pedal is properly assigned to SUSTAIN, SOSTENUTO, and SOFT (page 128). • The damper pedal has no effect, or the sound continuously sustains even when the damper pedal is not pressed. The pedal cable/plug may not be properly connected. Make sure to securely insert the pedal plug into the proper jack (page 150 - 151). • Not all simultaneously-played notes sound. You may be exceeding the maximum polyphony of the PF-1000. When this happens, the earliest played notes will stop sounding, letting the latest played notes sound. See page 154 for information on the maximum polyphony. • Accompaniment style or Song playback does not start. • MIDI Clock may be set to “EXTERNAL.” Make sure this is set to “INTERNAL” (page 135). • Make sure to press the appropriate [START/STOP] button. To play an accompaniment style, press the STYLE CONTROL [START/STOP] button (page 61); to playback a song, press the SONG [START/STOP] button (page 74). •“New Song” (a blank song) has been selected. Make sure to select an appropriate song in the SONG display (page 74). • The song has been stopped at the end of the song data. Return to the beginning of the song by pressing the [TOP] button (page 76). • Only the rhythm channel plays. Make sure the Auto Accompaniment function is turned on; press the [ACMP] button. • The accompaniment style does not start, even when Synchro Start is in standby condition and a key is pressed. You may be trying to start accompaniment by playin...