Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
FUEL HANDLING Fuel CAUTION! The machine is equipped with a two-stroke engine and must always been run using a mixture of gasoline and two-stroke engine oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained.When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture. ! WARNING! Always ensure there is adequate ventilation when handling fuel. Mixing • Always mix the gasoline and oil in a clean container intended for fuel. • Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline. • Mix (shake) the fuel mixture thoroughly before filling the machine’s fuel tank. Gasoline CAUTION! Always use high grade oil mixed gasoline (minimum 87 RON). • This engine is certified to operate on unleaded gasoline. • The lowest recommended octane rating is 87. If you run the engine on lower octane rating than 87 so-called “knocking“ can occur. This leads to an increased engine temperature, which can result in a serious engine breakdown. • When working at continuous high revs a higher octane rating is recommended. Two-stroke oil • For best results and performance use HUSQVARNA two- stroke oil, which is specially formulated for our two-stroke engines. Mixture 1:50 (2%). • If HUSQVARNA two-stroke oil is not available, you may use another two-stroke oil of good quality that is intended for air cooled engines. Contact your dealer when selecting an oil. • Never use two-stroke oil intended for water-cooled outboard engines, sometimes referred to as outboard oil. • Never use oil intended for four-stroke engines. Gasoline, litre Two-stroke oil, litre 2% (1:50) 5 0,10 10 0,43/0,20 15 0,30 20 0,40 US gallon US fl. oz. 1 2 1/2 2 1/2 6 1/2 5 12 7/8 • Do not mix more than one month’s supply of fuel at a time. • If the machine is not used for some time the fuel tank should be emptied and cleaned. • This engine is certified to operate on unleaded gasoline. Fueling ! WARNING! Taking the following precautions, will lessen the risk of fire: Do not smoke or place hot objects near fuel. Always shut off the engine before refuelling. Always stop the engine and let it cool for a few minutes before refuelling. When refuelling, open the fuel cap slowly so that any excess pressure is released gently. Tighten the fuel cap carefully after refuelling. Always move the machine away from the refuelling area before starting. • Move the machine at least 10 ft (3 m) from the refuelling point before starting it. •Clean the area around the fuel cap. Contamination in the tank can cause operating problems. •Ensure that the fuel is well mixed by shaking the container before filling the tank. 12 – English English – 13 STARTING AND STOPPING Starting and stopping Cold engine Ignition: Set the stop switch to the start position. Start position is achieved by moving the stop switch slightly backwards (356BT) or downwards (356BF) until the stop switch clicks into start position. It is not allowed to set the stop switch in full throttle position. Choke: Set the choke control in the choke position. Primer bulb: Press the air purge repeatedly until fuel begins to fill the bulb. The bulb need not be completely filled. Warm engine Use the same starting procedure as for a cold engine but without setting the choke control in the choke position. Starting Hold the body of the machine on the ground using your left hand (CAUTION! Not with your foot!). Grip the starter handle, slowly pull out the cord with your right hand until you feel some resistance (the starter pawls grip), now quickly and powerfully pull the cord. Never wrap the starter cord around your hand Repeat pulling the cord until the engine starts. When the engine starts, return choke control to run position. CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine. Stopping The engine is stopped by moving the stop switch to the stop position. ! WARNING! Always move the machine away from the refuelling area before starting. Place the machine on a flat surface. Make sure no unauthorised persons are in the working area, otherwise there is a risk of serious personal injury. The safety distance is 15 metres. The machine may only be started in its complete design. If the machine is started without all the guards fitted there is a risk of personal injuries. MAINTENANCE Carburetor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in.To ensure that it continues to run at peak performance and to minimise harmful exhaust emissions after the running-in period, ask your dealer/service workshop (who will have a rev counter at their disposal) to adjust your carburettor. Function The carburetor gover...