Votos - , Puntuación media:
(
)
)
Fabricar: Husqvarna
Tamaño del archivo: 1.37 mb
Nombre del archivo: HOUS2007_O0503015.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
6. Never attempt to unclog the collection system until the mower’s engine engine has been shut off and all moving parts have come to a complete stop. 7. Do not stand behind the vent at the rear of the collection system due to the potential for small pieces of blowing debris to escape through the vent. 8. Wear eye and ear protection. 12 SERVICE AND MAINTENANCE Transport WARNING The collection system bags must be completely empty or removed while driving forward onto a trailer. If the mower must be loaded onto a trailer while there is still debris in the container, the mower must be backed up onto the trailer to avoid tipping. Cleaning and Washing Regular cleaning, washing, and lubricating will prolong the service of the machine. NOTE: Use care with power washers to avoid damage to decals. Limit direct spray on these items. DO NOT EXCEED 1000 PSI WATER PRESSURE FOR CLEANING. For best results, clean poly mesh inside hood regularly. Instructions for doing this can be found in the Service section of this manual. Storage 1. Clean machine. 2. Cover all scratches with touch-up paint. 3. Covered or indoor storage is recommended. Preventative Maintenance Schedule Item Before Each Use Every 5 Hours Every 25 Hours Every50 Hours Inspect/Clean Poly Mesh X X Check/Tighten Nuts & Bolts X Check/Tighten Hoses X Turn Hose End to End X Rotate Hose X Clean Machine X Inspect Bags X 13 SERVICE AND MAINTENANCE Caring For Hoses 1. Inspect hoses before each use. If hoses have excessive wear, tears, or punctures, replace immediately. 2. To prolong the life of the hose, periodically rotate hose and turn hose end to end. Refer to Preventative Maintenance Schedule in this manual. 3. Avoid twists and sharp turns in the hoses, as they will increase wear on the hoses. 4. Avoid dragging the lower hose along the sides of buildings or other hard surfaces. Cleaning Poly Mesh The poly mesh on the collection system is located inside the container hood. For best results, clean poly mesh regularly. Cleaning Instructions 1. Shut off engine. 2. Release the two (2) rubber latches under the rear of the hood. Open hood and brush debris off of both sides. 3. Close hood and re-latch. DO NOT USE THE COLLECTION SYSTEM WITHOUT POLY MESH SECURELY IN PLACE. Caring For Bags Inspect the bags before each use. If bags have excessive wear, tears or punctures, replace immediately. Cleaning Instructions NOTE: Under normal usage the bag material is subject to deterioration and wear. 14 SERVICE AND MAINTENANCE Troubleshooting Guide DANGER Before servicing unit, wait for all moving parts to come to a complete stop. Turn engine off and remove the spark plug wire. PROBLEM POSSIBLE CAUSE CORRECTION Loss of Vacuum. Unusual vibration or noise. Unit difficult to close. 1. Blower, hose or hood inlet clogged. 2. Bags full. 3. Fan blades bent or broken. 4. Poly mesh plugged. 1. Solid object jammed in unit. 2. Loose or missing bolts on unit. 3. Bent or damaged fan. 1. Obstructions keeping door from completely closing. 2. Hood hinge bolts too tight. 1. Remove hose and clean inlet. 2. Inspect and empty. 3. Replace/repair impeller. 4. Clean poly mesh. 1. Check and remove any obstruction. 2. Tighten or replace bolts. 3. Replace/repair impleller. 1. Clear obstructions. 2. Loosen bolts. 15 16 NOTE: Your Front Weight Bar may look different from those shown in this diagram. SPINDLE DRIVE ASSEMBLY PARTS ILLUSTRATIONS 17 18 HOOD ASSEMBLY 539 97 69-79 (x 8) 539 11 11-77 (x 2) 539 99 06-13 (x 2) 539 99 07-30 (x 2) 539 20 06-84 (x 30) 539 99 05-98 (x 16) 539 97 69-78 (x 8) 539 20 06-84 (x 30) 539 20 06-84 (x 30) 539 20 06-84 (x 30) 539 99 05-98 (x 16) 539 99 10-03 (x 8) 539 11 11-82 539 11 13-39 539 11 17-55 539 11 11-83 539 10 27-44 (x 11) 539 10 54-08 (x 12) 539 10 27-44 (x 11) 539 11 11-74 539 11 11-86 (x 6) 539 97 69-77 (x 6) 539 20 04-78 (x 2) 539 11 11-86 (x 6) 539 11 12-60 539 11 11-72 539 11 00-33 (x 8) 539 11 11-81 (x 2) 539 99 06-45 (x 6) 539 11 11-75 (x 2) 19 HITCH ASSEMBLY 539 11 11-58 (x 2) 539 11 11-87 (x 4) 539 99 05-80 (x 3) 539 99 02-54 (x 4) 539 99 06-25 (x 4) 539 11 11-67 539 11 11-71 539 97 69-78 (x 3) 539 97 69-79 (x 22) 539 10 13-31 (x 2) 539 11 11-90 539 97 72-50 (x 2) 539 99 05-63 (x 20) 539 97 69-79 (x 22) 539 11 11-55 539 99 06-13 (x 2) 539 99 06-55 (x 2) 539 10 83-69 (x 2) 539 99 05-63 (x 20) 539 97 69-79 (x 22) 539 11 12-67 (x 2) 539 11 11-57 539 97 69-79 (x 22) 539 97 69-79 (x 22) 539 99 05-63 (x 20) 539 11 11-62 (x 2) 539 99 05-63 (x 20) 20 BLOWER ASSEMBLY LOCKING COLLAR THIS SIDE UP THIS SIDE DOWN HUB DOWN 539 10 25-35 539 99 07-17 (x 12) 539 99 01-96 (x 3) 539 10 67-86 (x 2) 539 11 13-31 539 10 67-41 539 10 81-20 (x 12) 539 99 00-74 (x 10) 539 10 04-72 (x 3) 539 11 13-32 539 88 03-16 (x 7) 539 11 12-27 539 10 26-91 (x 5) 539 10 26-91 (x 5) 539 10 67-86 (x 2) 539 11 12-29 (x 3) 539 11 17-47 539 11 12-25 539 99 07-17 (x 12) 539 10 20-67 539 11 08-13 539 10 22-44 (x 3) 539 10 67-13 539 10 65-04 539 99 02-47 539 10 01-41 539 99 05-98 (x 12) 539 11 12-29 (x 3) 539 ...