Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
To give the fingers a new square raking edge, remove the end plates and turn the entire main shaft assembly 180° and replace it on the Turf Rake. NOTE: Use Pro-Lock (retaining 1, medium strength) on the 7” pulley on the main shaft. To prolong the life of the main shaft, extra holes are provided. If the circular holes holding the satellite shafts become distorted, rotate all four satellite shafts to the next set of holes. Seeding/Multipurpose Height The seeding/multipurpose blades are used for cutting grooves for over-seeding and can also be used for verticutting grasses. To set the height properly place unit on the lawn surface and adjust the wheel height up (see Fig. 4 ). Adjusting the wheel height up lowers the blades. Seeding The proper height setting for over-seeding is approximately 1/4” into the ground. Adjust the wheel height up approximately one notch. If set deeper, grass seed being applied may not germinate. For best results, over-seed in two passes of 1/2 application rate at right angles or in a criss-cross pattern. Water heavily immediately after seeding then lightly for 10-14 days keeping soil moist. Slicing The proper height setting for slicing or aerating is 1/2” to 3/4” into the ground. Adjust the wheel height up one or two notches. For crawling grasses such as Zoysia, Bermuda, Bahia, etc. raise the wheels only one notch. Crawling grasses should not be sliced too deeply. For single strand grasses like Bluegrass or Rye, aerate in perpendicular directions for more even slicing. For example, slice in a North-South direction on the first pass, switching to an East-West direction on the second pass. As the seeder/multipurpose blades wear they may be rotated to provide a new cutting edge. The wheels may be raised to allow the blades to penetrate deeper into the ground. CAUTION BE CERTAIN THAT THE SET SCREWS ARE TIGHTENED PROPERLY IN BEARINGS AND PULLEY WHEN REASSEMBLING. Fig. 4 Slicing Height The slicer blade assembly is recommended for slicing, verticutting or aerating when a thinner blade is preferred. This is the recommended blade for use on golf course greens. To set the height properly place unit on the lawn surface and adjust the wheel height up (see Fig. 4). Adjusting the wheel height up lowers the blades. The proper height setting for slicing or aerating is 1/2” to 3/4” into the ground. Adjust the wheel height up one or two notches. For crawling grasses such as Zoysia, Bermuda, Bahia, etc. raise the wheels only one notch. Crawling grasses should not be sliced too deeply. For single strand grasses like Bluegrass or Rye, aerate in perpendicular directions for more even slicing. For example, slice in a North-South direction on the first pass, switching to an East-West direction on the second pass. As the slicer blades wear they may be rotated to provide a new cutting edge. The wheels may be raised to allow the blades to penetrate deeper into the ground. CAUTION BE CERTAIN THAT THE SET SCREWS ARE TIGHTENED PROPERLY IN BEARINGS AND PULLEY WHEN REASSEMBLING. GENERAL MAINTENANCE TO KEEP THE TRS-20/TSS-20 INGOOD OPERATING CONDITION, PERFORM THE FOLLOWING: • When replacement parts are required, use genuine Classen parts or parts with equivalent characteristics including type, strength, and material. Failure to do so may result in product malfunction and possible injury to the operator and/or bystanders. • Keep all safety decals legible. Remove all grease, dirt and debris from decals. Any safety decal that becomes illegible should be replaced immediately (see ‘Safety Decals” section). Safety decals can be affixed by peeling off the backing and applying to clear, dry surface. Smooth out to remove any air bubbles. • Do not operate equipment without shields in place. • Do not make any adjustments or perform any maintenance while the engine is running. • Check engine mounting bolts frequently to maintain proper tightness. • Thoroughly clean off blades when application is completed and apply a light coat of oil to prevent rust on blades. • Keep belt free of oil and dirt. • Check for worn or deteriorating components that could create a hazard. When new components are installed, be sure that current safety decals are affixed to the replaced components. Safety decals can be affixed by peeling off the backing and applying to clear, dry surface. Smooth out to remove any air bubbles. ENGINE MAINTENANCE • Refer to engine manufacturer’s Owner’s Manual. • Check engine oil level with engine resting in a level position. • Inspect air filter element and replace if necessary. • If carburetor adjustment is necessary, stand to one side and keep feet and hands clear while making adjustments. MACHINE STORAGE SAFETY WARNING TO PREVENT POSSIBLE EXPLOSION OR IGNITION OF VAPORIZED FUEL, DO NOT STORE EQUIPMENT WITH FUEL IN TANK OR CARBURETOR OR NEAR OPEN FLAME (I.E. FURNACE, WATER HEATER, PILOT LIGHT). STORAGE INSTRUCTIONS Before the TRS-20/TSS-20 is put into storage for any period exceeding 30 days, the following steps shoul...
Otros modelos de este manual:Los sistemas de ventilación - TRS-20 (1.36 mb)
Los sistemas de ventilación - TRS-20 (1.36 mb)
Los sistemas de ventilación - TSS-20 (1.36 mb)