Votos - 3, Puntuación media: 3.7 ( )

Fabricar: Shindaiwa Tamaño del archivo: 697.53 kb Nombre del archivo: Idioma del manual:

See figure 7. 4. Using your right hand, pull the starter handle slowly until you feel the starter engage. 48006 Throttle Positions Full Throttle WARNING! The engine cover will be hot after blower operation! Engine Idle Lock Lever Stop Figure 5 Choke Control (open position shown) 48008 48007 Pull upward rapidly Fuel Primer Bulb Figure 7 Figure 6 8 5. As the starter engages, pull the starter handle upward rapidly. 6. If necessary, repeat Steps 4 and 5 2–3 times until the engine starts. WHEN THE ENGINE STARTS 1. As the engine warms, open the choke gradually by slowly moving the choke control down to the fully OPEN position. 2. Run the engine at idle speed until operating temperature is reached (2-3 minutes). The blower should now be ready for use. STOPPING THE ENGINE 1. Cool the engine by allowing it to run at idle for 2–3 minutes. 2. While squeezing the throttle lock lever, push and hold the throttle lever down until the engine stops. See figure 8. IMPORTANT! If the engine continues to run with the throttle lever in the “off” position, stop the engine by moving the choke control UP to the fully closed position. Adjust idle setting as decribed on page 10. IF THE ENGINE DOES NOT START Repeat the appropriate starting procedures for “warm” or “cold” engine. If the engine still will not start, follow the “Starting a Flooded Engine” procedure as below: STARTING A FLOODED ENGINE 1. Disconnect the spark plug lead, and use the spark plug wrench to remove the spark plug in a counter- clockwise direction (see the diagram on page 14). 2. If the spark plug is fouled or is soaked with fuel, clean or replace the plug as required. 3. Clear excess fuel from the combustion chamber by cranking the engine several times while the spark plug is removed. 4. Install and tighten the spark plug, and reconnect the spark plug lead. 5. Repeat the starting procedures for “warm engine.” 6. If the engine still fails to start or fire, refer to the troubleshooting flow chart at the end of this manual. CAUTION! The recoil starter can be damaged by abuse! n Never pull the starter cord to its full length. n Always engage the starter before cranking the engine. Always rewind the starter cord slowly. WARNING! Never operate the blower unless all controls are properly installed and in good working order. Never operate the blower if the intake cover or blower tubes are missing or damaged! 48009 Throttle Lever Squeeze Lock Lever Push Down To Stop Figure 8 9 ADJUSTING ENGINE IDLE SPEED 1. Start the engine by following the procedures described on the preceding pages. Make sure the thottle lever is in the "idle" position. 2. Run the engine at idle speed until operating temperature is reached (2-3 minutes). 3. Loosen the throttle cable locknut. See figure 9. 4. Turn the cable adjuster in or out until the engine idles smoothly at approximately 2500-3000 rpm. n Turn the throttle cable adjuster clockwise to decrease engine idle speed. n Turn the throttle cable adjuster counter-clockwise to increase engine idle speed. 5. Tighten the throttle cable locknut securely. IMPORTANT! A clean and unrestricted airflow is essential to your blower’s engine performance and durability! Before attempting any carburetor adjustments, inspect and clean the engine air filter as described on page 13 of this manual. IMPORTANT! Blower tubes and intake cover must be in place while adjusting engine idle! Engine idle speed will also be affected if either the intake cover or blower tubes are blocked or incorrectly installed! Idle Decrease Idle Increase 48010 Cable Adjuster Throttle Cable Locknut Figure 9 10 ADJUSTING THE HARNESS The Shindaiwa EB501 Blower features an advanced harness system that helps ensure maximum operator comfort and ease of operation. n The shoulder harness is filled with soft padding for reduced operator fatigue. n The simplified adjustment system makes it easy to match the harness to every body size and type. See figure 10. Adjustment Holes Adjusting Strap The adjusting strap lets the user determine how far apart the upper harness loops are positioned. Easy to customize for maximum comfort. 48019 Comfortable Back Pad Pull on the loops to quickly tighten the harness straps Quick-disconnect Spring Hook Quick-adjust Buckle 48019B To tighten straps… To loosen straps… 48019A Pull the quick- adjust buckles up… Quick-adjust Buckle Pull strap loops down …and pull the straps down. Figure 10 11 USING THE BLOWER THINK SAFETY! OPERATING TIPS In the hands of an experienced operator, the EB501 can efficiently move a wide variety of debris ranging from grass clippings to gravel. As a general rule, operate your EB501 at the lowest throttle setting required to get the job done: n Use low throttle settings when clearing lightweight materials from around lawns or shrubbery. n Use medium to higher throttle settings to move grass or leaves from parking lots or walkways. n Use full throttle when moving heavy loads such as dirt or snow. IMPORTANT! Blower noise increases at higher thro...

Descargar ahora

Introduzca dos números de la imagen: