Votos - 2, Puntuación media: 4 ( )

Fabricar: Echo Tamaño del archivo: 1.69 mb Nombre del archivo: Idioma del manual:

2. Replace drain plug, remove fill plug and fill with new oil. See engine manual for oil specifications. 3. Start and run engine for 30 seconds. Stop engine. 4. Wait 30 seconds, then re-check oil level. 5. Top off if necessary. See engine manual for details. ADJUSTMENTS DEFLECTOR LEVER If the deflector door moves from the set position during operation, tighten the deflector lever pivot bolt just enough to keep the deflector in place. DO NOT over tighten, the handle tube could crush. HORIZONTAL DEFLECTOR Adjust the jam nuts on the cable conduit so the deflector door is completely closed when the deflector lever is moved all the way forward. (Figure 1) DEFLECTOR CHAIN The sprocket needs to be installed on the deflector as shown. The chain consists of 2 master links, 6 roller links, and 5 pin links. The middle pin link should be over the center tooth of the sprocket. (Figure 2) If large amounts of adjustment are required, the chain can be moved one pitch on the sprocket to gain 1/2” of adjustment. FIGURE 1 FIGURE 2 STORAGE To prevent possible explosion or ignition of vaporized fuel, do not store equipment with fuel in tank or carburetor in an enclosure with open flame (for example, a furnace or water heater pilot). Before the equipment is put into storage for any period exceeding 30 days. 1. Drain all fuel from the fuel tank and fuel lines. 2. Start the engine and run until all the fuel is used from the carburetor float bowl and the engine stops. 3. While the engine is still warm, drain the crankcase oil and replace with the proper weight oil corresponding to the season the equipment will be next used. 4. Remove the spark plug and squirt a small amount of engine oil into the cylinder. Slowly pull the starter a few times to distribute oil in the cylinder and reinstall the spark plug. 5. Top off if necessary. See engine manual for details. To put the equipment into service after an extended period of storage. 1. Check for loose parts and tighten if necessary. 2. Fill the fuel tank and then check the engine oil level. 3. Start the engine and check for fuel leaks. Repair any leaks before operating the unit. STORAGE / TORQUE SPECIFICATIONS TORQUE SPECIFICATIONS Location Description P/N Min. Torque Ft-lbs (In-lbs) Max. Torque Ft-lbs (In-lbs) Housing to engine face BLT-W LF 5/16-24 x 1-3/8 910517 22 28 Engine to deck BLT 5/16-18 X 1-1/2 64262-009 19 25 Fan to Crankshaft BLT-HEX 7/16-20 x 1-3/4 GR8 (USED ON 9270 MODELS) 64123-253 50 90 BLT-HEX 3/8-24X1-3/4 GR8 (USED ON 9390 AND 9400 MODELS) 64123-127 30 50 BLT-HEX 3/8-24 X 2.5 GR 8 (USED ON 9570 MODELS) 64123-267 30 50 LITTLE WONDER BLOWER INTAKE GUARD ASSY FIGURE 1 123561071189810711449 ITEM PART NO. DESCRIPTION QTY 1 4166183 LABEL-INTAKE GUARD 1 2 4165218.7 ASSY-GUARD INTAKE 1 3 64123-54 BLT-HEX 5/16-18X.75 4 4 64268-02 NUT-FL NYLON LOCK 5/16-18 6 5 64229-02 NUT 5/16-18 4 6 4165926.10 INTAKE PANEL-CENTER 1 7 64123-253 BLT-HEX 7/16-20 x 1-3/4 GR8 1 (USED ON 9270 MODELS) 64123-127 BLT-HEX 3/8-24X1-3/4 GR8 (...

Descargar ahora

Introduzca dos números de la imagen: