Votos - 4, Puntuación media: 4.8
(
)
)
|
Resumen del manual
n While printing, do not open the door or covers. o While printing, do not unplug the power cord. a While printing, do not move the machine. n Keep corrosive liquids, such as acid, off the machine. a Do not allow paper clips, staples, or other small objects to fall inside the machine. a Open and close the door and covers softly. a Do not put anything except originals or command sheets on the machine. n Do not spill liquid on the machine. o When opening or closing the door or covers, keep hold of them so they don’t full. a If you clean rubber parts with benzine, wipe them with a dry cloth afterwards. General Safety Information D Always turn the machine off when you have finished printing for the day. D When the machine will not be used for long periods, disconnect the power cord. D If the machine must be transported by vehicle, please contact your service representative. GUIDE TO COMPONENTS 1. Platen Cover Lower this cover over an original before printing. 2* Front Door Open for access to the inside of the machine. 3. Side Plate Fine Use to shift the paper feed table sideways. Adjusting Dial 4. Paper Feed Table Press to lower the paper feed table. Down key or Change Paper key When you have an optional large capacity tray, this key is used to remove paper. 5. Paper Feed Side Use to prevent paper skew. Plates 6. Paper Feed Table Set paper on this table for printing. 7. Separation Roller Use to adjust the separation roller pressure to Pressure Levers prevent double feed. 8. Feed Roller Use to adjust the contact pressure of the pa- Pressure Lever per feed roller according to paper thickness. 9. Original Table Use to open the original table unit when install- Release Lever ing the master. 10.Original Holder Convenient place for holding originals while operating the machine. 11.Operation Panel Operator controls and indicators are located here. = See page 6. 12. Behind Cover Open to access the CS Mode key and so on. = See page 6. INSTALLATION REQUIREMENTS INSTALLATION REQUIREMENTS The machine’s location should be carefully chosen because environmental conditions can affect its performance. Optimum Environmental Conditions J Temperature: 10 – 30”C, 50-86°F a Humidity: 20-90?40RH rJ A strong and level base (a sturdy desk and cabinet etc.). D The machine must be level within 5 mm, 13/64” both front to rear and left to right. n Make sure to locate this machine in a large well ventilated room that has an air turnover of more than 30 m3/hr/person. Environments To Avoid Direct sunlight or strong light (more than 1500 Iux). Locations directly exposed to cool air from an air conditioner or heated air from a heater. (Sudden temperature changes from low to high or vice versa may cause condensation within the machine.) !J Dusty areas. Access To The Machine CJ Place the machine near a power source, providing clearance as shown. Main Frame Morethan20cm,8.0$ Morethan d-k%1I t More than 60cm,23.7” OPERATION H c1 c1 * b fl c1 Press the Master Making key. A trial print is delivered to the paper delivery table. Press the Proof key and check the image density and the image position of the proof print. If the image position is not correct, adjust it using the Image Position keys or the fine adjustment dial. (~ See pages 21 and 22.) If the image density is slightly dark or light, adjust the image density by pressing the Speed keys. (* See page 23.) Press the Print Start key. After printing is completed, the same number of prints is automatically set for the next job. if you want to stop the machine during a print run, press the Stop key. Remove the prints from the paper delivery table. To clear all the modes you have selected, press the Clear Modes key. If A4, 81/2” x 11” or smaller paper is not delivered to the paper delivery table properly, set the small size end plate prop to the small size paper delivery end plate. * See page 16. Master Making Stop I @ oo~” : Print SWt m PrFl%tSW Proof c1 4 Q #l ;o~ nter OPERATION Reduction/Enlargement Printing Original , Prjnt Paper Feed Dwection c’ L ~Constant D The center and the leading edge of the print image do not shift when a print image is made with this function. Reduction Prints can be reduced in size by using the Reduce/Enlarge key. — Metric version — * 93 ?40 1, 87 Yo l--f?++ 82 ?40 B4 A4 65 0/0 B5 A5 ~ A3 , A4 71 ?40 A4 A5 B4 B5 * Select this ratio when you make prints with a lot of edge margins. OPERATION nSelect the tio using desired reduction rathe Reduce/Enlarge H-— bjlx~q .al Ld4 *V aft 4 nMake sure that the nrint DaDer.. 11 size: the are original and the correct % Set your original on the exposure glass or in the optional document feeder. Press the Check the Master Making key. image position of the trial or proof print. If the image position is not correct, adjust it using the Image Position keys (see page 21) or the side plate fine adjusting dial (* see page 22). Make your prints. OPERATION Directional Magnification Printing You can select independent ratios for vertical and hor...