Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
FED B A C Figure 1 – Datalogic Jet ™ Ethernet Multi Cradle General View Key: A) Link LED for Ethernet Port 1 B) Speed LED for Ethernet Port 1 C) Datalogic Jet™ Charging Status LED D) Power supply connector E) Ethernet Port 1 (with integrated Link and Speed LEDs) F) Ethernet Port 2 (with integrated Link and Speed LEDs) 822000751 (Rev. A) The Ethernet cradle drivers are pre-installed on the Datalogic Jet™ and initiate automatically when the Datalogic Jet™ is placed in a properly connected Four Slot Ethernet cradle. When the mobile computer is inserted into the Four Slot Ethernet cradle, the LAN icon indicates that the mobile computer is connected to a network. Ethernet communication requires Datalogic Jet™ PDA SW version 5.41 or later. Verify the software version by tapping on Software – Version in the Datalogic default home page. Otherwise, search for the file version.htm under the Windows folder. NOTE The green Speed LED lights to indicate that the transfer rate is 100 Mbps. When it is not lit it indicates that the transfer rate is 10Mbps. The maximum bandwidth capacity for each Mobile Computer is 12Mbps. NOTE The yellow Link LED blinks to indicate activity, or stays lit to indicate that a link is established. When it is not lit it indicates that there is no link. The Speed LED and the Link LED integrated in Ethernet Port 1 and 2 function in the same way. The Charging Status LED on the mobile computer shows the status of the battery charging. The maximum time required to recharge a completely run-down battery pack is about 2.5 hours for Li-Ion batteries. See Datalogic Jet™ User’s Manual par. 3.5.1 for Charging Status LED indications. Correct Mobile Computer Insertion / Removal Insert the mobile computer into a slot to begin charging and start communication. For correct insertion onto the cradle, insert the mobile computer from the top of the cradle and push it down firmly. Figure 2 - Mobile Computer Insertion To remove the mobile computer from the Datalogic Jet™ Ethernet Multi Cradle, simply pull it upwards while holding the cradle firmly down. TECHNICAL FEATURES Electrical Features Power supply * from 12 to 14 VDC ± 5% Consumption Max 4.2 A Indicators Ethernet Link LED (yellow) Ethernet Speed LED (green) Charge time (when PDA is off) max 2.5 hours (Li ION batteries) Communication Features Interface Ethernet 10/100 Base T Environmental Features Working temperature 0° to +50°C / 32° to 140°F ** Storage temperature -20° to +70°C / -4° to 158°F Humidity 90% non condensing Degree of protection IP20 Mechanical Features Dimensions 480 x 110 x 190 mm 18.89 x 4.33 x 7.48 in Weight about 2750 g / 97 oz * Recommended DL power supply: FPS18. * * Batteries must be charged at a temperature ranging from 0° to 45 °C (+32° to 113°F). CONNECTIONS Connections should always be made with power OFF! CAUTION Ethernet Connection Connect the Ethernet cradle (Ethernet port 1) to an Ethernet hub or a port on the host device. Connect the Ethernet cradle (power port) to power supply. D A B C Figure 3 - Ethernet Connection Key: A) Datalogic Jet™ Ethernet Multi Cradle B) 94ACC4595 FPS18 power supply without power cord 94ACC1150 Power cord EU 3-pin C) UTP CAT 5E cable (recommended use) D) Ethernet hub Daisychaining Ethernet Connection To connect several cradles to an Ethernet network, Ethernet cradles may be daisychained. It is recommended not to connect more than 4 cradles in order to maintain the optimal baud rate. The Speed LED and the Link LED on the Ethernet Port 2 function in the same way as the Speed LED and the Link LED on the front of the cradle. To daisychain cradles: 1. Connect the first Ethernet cradle to power and to the Ethernet Switch as shown on Figure 4. 2. Connect power to the second Ethernet cradle. 3. Connect the daisychain Ethernet cable (either straight or twisted cable can be used) between Ethernet Port 2 of the first cradle, and Ethernet Port 1 of the second cradle. 4. Connect additional in Figure 4. D CBA E Figure 4 - Daisychaining Ethernet Connection Key: A) Ethernet hub B) Ethernet Port 1 C) Ethernet Port 2 D) 94ACC4595 FPS18 power supply without power cord 94ACC1150 Power cord EU 3-pin E) UTP CAT 5E cable (recommended use). Power Supply Each Ethernet Multi Cradle requires a power supply to be connected to the cradle. We recommend the DL FPS18 power supply. VEXT GND Figure 5 - Power Supply Polarity Datalogic Mobile S.r.l. Via S. Vitalino 13 40012 - Lippo di Calderara Bologna - Italy dichiara che declares that the declare que le bescheinigt, da. das Gerat declare que el DL JET Ethernet Desk Multi Cradle e tutti i suoi modelli and all its models et tous ses modeles und seine Modelle y todos sus modelos sono conformi alle Direttive del Consiglio Europeo sottoelencate: are in conformity with the requirements of the European Council Directives listed below: sont conformes aux specifications des Directives de l'Union Europeenne ci- dessous: den nachstehenden angefuhrten Direktiven des Europaischen Rats: cumple con lo...