Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
This setting pertains only to units configured for EAS Coupled Mode. Reference the “EAS Mode ” description for more information about Coupled and Decoupled EAS operation. Also reference “EAS Retry Count .” NOTE To set the EAS Deactivation Duration — Manual: 1. Scan the SWITCH bar code. 2. Scan the bar code, SET EAS DEACTIVATION DURATION — MANUAL below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan. 3. Scan the appropriate digits from the keypad in Appendix C that represent the desired duration. The selectable range is 1-255, which is the duration in 50-millisecond increments. Pad all single and double digit numbers with leading zeroes to yield a 3-digit entry (001-255). Examples: 001 = 50ms 008 = 400ms 050 = 2,500ms (2.5 seconds) The scanner will automatically exit Programming Mode when the appropriate amount of digits have been scanned SET EAS DEACTIVATION DURATION — MANUAL 6-58 Magellan® 9500 Interface Related Features Interface Related Features Interface Type Specifies the current scanner interface. Selections are: INTERFACE TYPE INTERFACE IDENTIFICATION NUMBERa RS-232 Standard 05 RS-232 Wincor-Nixdorf 12 RS-232 Single Cable 20 IBM USB 45 IBM Port 17 04 NOT USER-SELECTABLE Null Interface Indicated by 7-segment FRU display flashing 0 at start-up a. To access a scanner’s interface identification number, place the scanner in Scanner Diagnostic Mode and view the 7-segment FRU display (reference Scanner Diagnostic Mode in Chapter 2 for more information). A new scanner may have been shipped from the factory with a Null Interface (no interface type selected) to ensure system compatibility at installation. In this case, the correct Interface Type programming bar code must be scanned first before the scanner can be used with a POS system. NOTE If the scanner’s interface type must be changed, always be sure that interface configuration is the FIRST item scanned during a programming session. (Selecting an interface type resets ALL other configuration items to the factory default for that interface type.) NOTE Product Reference Guide 6-59 Interface Type — continued To select the desired interface: Great care should be taken to select the correct interface type, since you can cause damage to the scanner and/or POS terminal by attempting to change to an incompatible interface. ALWAYS make interface selections with the host cable DISCONNECTED. CAUTION When an interface is selected, the scanner loads the factory configuration for that interface as the selection is made, erasing any and all custom configuration that may have previously been done. NOTE 1. Disconnect current interface cable(s) if currently connected. 2. Scan the SWITCH bar code 3. Scan the bar code representing the appropriate interface located on the following pages. You’ll need to cover any unused bar codes adjacent to and on any facing pages to ensure the scanner reads only the bar code you intend to scan. 4. Complete the programming sequence by scanning the SWITCH bar code. Once the correct interface has been set, it will be necessary to proceed to the appropriate pages in this manual that select parameters and options for that interface. For example, if RS-232 is selected, turn to the pages in this manual headed as features specific to the RS-232 interface. NOTE 5. Connect new interface cable(s). 6-60 Magellan® 9500 Interface Related Features RS-232 Interface Selection Remember to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan. Great care should be taken to select the correct interface type, since you can cause damage to the scanner and/or POS terminal by attempting to change to an incompatible interface. ALWAYS make interface selections with the host cable DISCONNECTED. CAUTION INTERFACE TYPE = RS-232 STANDARD Product Reference Guide 6-61 RS-232 Wincor-Nixdorf Interface Selection Remember to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan. Great care should be taken to select the correct interface type, since you can cause damage to the scanner and/or POS terminal by attempting to change to an incompatible interface. ALWAYS make interface selections with the host cable DISCONNECTED. CAUTION INTERFACE TYPE = RS-232 WINCOR-NIXDORF 6-62 Magellan® 9500 Interface Related Features RS-232 Single Cable Interface Selection Remember to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan. Great care should be taken to select the correct interface type, since you can cause damage to the scanner and/or POS terminal by attempting to change to an incompatible interface. ALWAYS make interface selections with the host cable DISCONNECTED. CAUTION Single cable installations require connection at the POS Terminal (host) port. The Scale Host port connecti...
Otros modelos de este manual:escáner / copiadora / impresora multifunción - 9504 (1.87 mb)