Votos - 3, Puntuación media: 3.7
(
)
)
|
Fotos y especificaciones Canon PIXMA MG5440 |
Otros manuales para este modelo:
Resumen del manual
.WPA/WPA2 • Failed to connect to the access point. Make sure that the passphrase entered for the access point is correct. If the problem is not resolved, there may be other causes. See also the sections below: • If the DHCP function of the access point is inactive, enable the DHCP function and configure wireless connection settings again. • For details on how to check or change the settings of the access point, refer to the manual supplied with the access point or contact its manufacturer. • WLAN setting list If the MAC address filtering is enabled on the access point, change settings so that the MAC address of the printer will be accepted. Follow the procedure below to check the MAC address of the printer. 1. Press the HOME button. 2. Display Setup, then press the right Function button. 3. Select Device settings, then press the OK button. 4. Select LAN settings > Confirm LAN settings > WLAN setting list to check MAC address. For details on how to change the settings of the access point, refer to the manual supplied with the access point or contact its manufacturer. If the problem is not resolved, there may be other causes. See also the sections below: • If the access point is configured to communicate using IEEE802.11n standard only and encryption is set to TKIP, change the encryption to something other than TKIP or change the communication standard to something other than IEEE802.11n, then configure wireless connection settings again. • If encryption is set to TKIP, IEEE802.11n cannot be used as the communication standard. • For details on how to change the settings of the access point, refer to the manual supplied with the access point or contact its manufacturer. • To perform Standard setup again 1. Press the HOME button (A). 2. Use the or button (B) to display WLAN setup, then press the left Function button (C). WPS • Cannot connect. Connections are being attempted from multiple access points simultaneously. The screen appears when connections are being attempted from multiple access points simultaneously. Wait for a while, then configure WPS settings again. Press the WPS button on only one access point. • Failed to connect. The screen appears when an error occurs. Check the access point settings, then configure WPS settings again. For details on how to check the settings of the access point, refer to the manual supplied with the access point or contact its manufacturer. • Timeout error. The screen appears when WPS setup was not completed within a specified time. • Is the network device (router, etc.) turned on? If the network device is already turned on, turn it off, then turn it back on. Advanced setup • The Target Access Point is Not Detected • Is the network device (router, etc.) turned on? If the network device is already turned on, turn it off, then turn it back on. • Check the access point name/network name and network password of your access point or router. • Are the computer and network device configured? • Are the access point and printer installed in an open space where wireless communications are possible? • Is the access point operating in IEEE802.11n (2.4 GHz), IEEE802.11g or IEEE802.11b? After checking the above points, press the left Function button (A) on the printer to search for the access point again. If the problem is not resolved, there may be other causes. See also the sections below: • If SSID broadcast (connection via "ANY" SSID, etc.) is disabled or the stealth mode is enabled on the access point, enable SSID broadcast (connection via "ANY" SSID, etc.) or disable the stealth mode, then press the left Function button on the printer to search for the access point again. • Select Directly enter the access point name in the Select access point screen. Wireless connection settings of the access point can be entered on the printer directly. • If "WPA/WPA2 Enterprise" is set as the security protocol (encryption standard) on the access point, change the security protocol (encryption standard) and configure wireless connection settings again. "WPA/WPA2 Enterprise" is not supported on this printer. • For details on how to change the security protocol (encryption standard) for the access point, refer to the manual supplied with the access point or contact its manufacturer. • Multiple access points with the same name exist. Do you want to use multiple access points? The message appears when multiple access points with the same name are found. When you have only one access point: Select Use one AccessPoint only, then press the OK button. Select the MAC address of the target access point on the displayed screen, then press the OK button. For details on how to check the MAC address of the access point, refer to the manual supplied with the access point or contact its manufacturer. When using multiple access points: Select Use multiple AccessPoints, then press the OK button. • An Unknown Access Point is Displayed Access points in use nearby may also be detected. • The Access Point Name is No...
Otros modelos de este manual:escáner / copiadora / impresora multifunción - PIXMA MG5450 (363.53 kb)