Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
4 counter-clockwise until you have reached the maximum first stage. •Cock the rifle. •Turn set screw No. 5 (first stage) counterclockwise until the triggerreleases. •Turn set screw No. 5 from this position approx. 1/4 turn clockwise. The trigger is now adjusted to single stage operation, there is no more first stage. Warning: Single stage triggers are very sensitive and must be operated with special care. The sear engagement of 5/100 mm is obtained after the action is closed. In combination with a minimum trigger weight there might be a malfunction and an increased risk (inadvertent shot release). 8. Change of single stage trigger into two-stage trigger •Turn trigger stop set screw No. 8 approx. 2 1/2 turns to the left (counter-clockwise) (adjust max. trigger stop longer). •Release the safety of the trigger and cock the rifle. •Turn set screw No. 5 approx. 2 1/2 turns clockwise. •You should now feel a second stage •To adjust the optimum sear engagement proceed according to paragraph 3. •Perhaps you have to adjust the first stage according to paragraph 4, the trigger stop according to paragraph 5, the trigger weight according to paragraph 1 and the first stage weight according to paragraph 2 to the desired values. 9. Malfunctions of the trigger due to wrong adjustment procedure If the trigger is not adjusted correctly malfunctions may occur. Tampering with the trigger adjustments will not result in any success. Therefore proceed as follows: After every change the function of the trigger must be checked. When the malfunction is removed check the desired trigger values and adjust them again if necessary. The trigger catches the firing pin, but the trigger does not release: •Make sure that the safety of the trigger is released. •Check if there is a trigger cam and that it is attached correctly. •The trigger stop set screw No. 8 is screwed in too much. Turn it a few turns to the left (counter-clockwise) until the cocking piston or firing pin will release again. The trigger does not catch the cocking piston or firing pin: •Set screw No. 4 (first stage) is screwed in too much. •Check to see if the spring is correctly attached and not defective. The first stage trigger is adjusted too tightly: •Turn set screw No. 5 stepwise 1/4 turn to the right (clockwise) until the firing pin is caught. Catch rebound spring is too weak or defective: •Send your trigger to the factory or your service center for inspection. 10. Safety On the left side of the trigger there is a safety lever. Please see chapter „Cocking, loading and safety operation“. 11. Maintenance Please see chapter „Cleaning, maintenance, care, lubrication“. Sight Set Folding rear sight and tangent rear sight 1. Elevation of folding rear sight: •Loosen slightly both screws at the rear sight •Shots are too low: Raise the slide •The shots are too high: Lower the slide 2. Elevation of tangent rear sight: •Shots are too low: Raise rear sight elevator •The shots are too high: Lower rear sight elevator 3. Windage of folding and tangent rear sight To adjust windage to left or right tap the base of the rear sight in the opposite direction of the desired change of impact, using a soft metal such as aluminum or brass punch. Scope mounts All ANSCHUTZ rifles have a grooved, 11 mm rail to accept mounts for a telescopic sight. Cleaning, Maintenance, Care, Lubrication Even after considerable use, your ANSCHUTZ small bore match rifle will not require much attention - a tribute to its solid design, first class materials, well proven ANSCHUTZ workmanship and precision. If you follow the recommendations below, you will help maintain the excellent performance of your rifle for a long time. Regular care after every shooting: •Please only use resin and acid free oils. •Remove any residues from the barrel. Clean with a lint-free cloth or pull cleaning cords several times through the barrel from chamber to muzzle to remove deposits. Subsequently pull a slightly oiled, lint-free cloth or cleaning cords through the barrel to avoid corrosion. •Clean the bolt and the loading tray with a slightly oiled cloth. •Make sure that the metal parts of your rifle are protected against corrosion by a slight oil film. Do not use exessive oil. •Remove the oil film with a dry cloth or cleaning cords before you shoot again. •Some ammunition leaves corrosive particles in the barrel. Therefore you should thoroughly clean and oil the barrel each time immediately after shooting to avoid corrosion. Accessories Please ask for our catalog or take a look at our websites under com or Warranty A warranty of 2 years will be issued. Parts which are subjected to wear are not part of this warranty. In the case of warranty we substitute the defective parts free of charge. Cases of warranty will only be accepted if the article in question and the corresponding purchase receipt plus filled-in warranty card are presented. Warranty will not be accepted if changes or repair works...