Votos - 3, Puntuación media: 3.3 ( )

Fabricar: Country Home Products Tamaño del archivo: 429.64 kb Nombre del archivo: Idioma del manual:

1. Place the chute (item 1) on the discharge hole (item 2) around the DR® SNOW THROWER. 2. Install the three retaining plates (item 3) using the six 1/4" x 1/2" bolts and flange nuts (items 4-5), tighten securely. Verify that the chute turns freely on the collar. Figure 2 DR® SNOW THROWER Safety, Operation & Maintenance Instructions ASSEMBLY & INSTALLATION ! WARNING: Before installing the DR® SNOW THROWER, always bring the DR® ALLTERRAIN ™ MOWER to a complete stop, shut off the engine and remove the spark plug wire. Step 3: Installation (Figure 3) 1. Remove the mowing deck from the DR® ALL-TERRAIN™ MOWER. 2. Apply grease on the shaft (item 6). 3. Remove bolts (item 5) from belt cover. 4. Remove the belt cover (item 4). 5. Align the DR® ALL-TERRAIN™ MOWER and DR® SNOW THROWER. Carefully, insert the shaft (item 6) of the ALLTERRAIN ™ MOWER into the female attachment on the SNOW THROWER. 6. Reinstall the collar and pin used with the mower to secure the SNOW THROWER. Step 4: Belt Installation (Figures 3 & 4) 1. Carefully install the drive belt (item 1) around the drive pulley (item 2) under the DR® ALL-TERRAIN™ MOWER. 2. Pull the tensioner (item 3) to reinstall the belt on the idler. Make sure that the V-belt is not twisted and fits correctly in the V-groove on the pulley. 3. Make sure to position the belt above the belt guide, as shown in figure 4. 4. Reinstall the belt cover (item 4) and bolts. Figure 4 Figure 3 DR® SNOW THROWER Safety, Operation & Maintenance Instructions ASSEMBLY & INSTALLATION DR® SNOW THROWER Safety, Operation & Maintenance Instructions Step 5: Rotation Handle Installation(Figure 5) 1. On the left side handlebar of the DR® ALLTERRAIN ™ MOWER, install the rotation handle support (item 1) at approximately 28" from the ground, using the U-bolt (item 2), plate and nuts. 2. Insert the plastic bushing (item 3, flange facing the operator) on the housing by pushing forward until it snaps. 3. Insert the worm shaft (item 4) in the plastic bushing. 4. Place the flat washer (item 5) and lock the shaft in place with the cotter pin (item 6). 5. Insert the plastic bushing (item 3, flange facing the operator) into the rotation handle support (item 1). 6. Insert the rotation handle (item 7) through the support then in the worm shaft (item 4). Secure with the hairpin (item 8). 7. Operate the handle and check for proper operation of the chute. ! WARNING: Make sure the chute blocks in both directions to prevent the snow from being projected in the operator's area (Figure 6). Figure 6 Figure 5 ASSEMBLY & INSTALLATION Step 6: Optional Drift Cutters -8173 Installation (Figure 7) 1. From the exterior of the housing, align the two square holes on the drift cutter (item 1) with the two round holes on the housing. 2. From the outside, insert the 5/16" x 5/8" carriage bolts (item 2). 3. Secure with two flange nuts (item 3). 4. Repeat on the other side. Figure 7 Removing the DR® Snow Thrower 1. Select a level surface, turn engine off and remove ignition key 2. Refer to Figure 5, Page 13. Remove hairpin (item 8) and rotation handle (item 7). 3. Refer to Figure 4, Page 12. Remove the belt cover (item 4). 4. Refer to Figure 3, Page 12. Pull the tensioner (item 3) to remove the drive belt (item 1). 5. Refer to Figure 3, Page 12. Unlock the pin (item 6) and carefully remove the DR® ALLTERRAIN ™ MOWER from the DR® SNOW THROWER. DR® SNOW THROWER Safety, Operation & Maintenance Instructions OPERATION Figure 9 Operating Controls The DR® SNOW THROWER is driven from the DR® ALL-TERRAIN™ MOWER drive pulley. ! WARNING: 1. Do not allow bystanders near working area. 2. Do not allow anyone to ride on the DR® SNOW THROWER. 3. Before cleaning, adjusting or repairing the DR® SNOW THROWER: bring the DR® ALLTERRAIN ™ MOWER to a complete stop, wait for all movement to stop, apply the parking brake, shut off the engine and remove the spark plug wire. 4. Never put any part of your body under the DR® SNOW THROWER while making adjustments. Chute Rotation Adjust the chute direction with the rotation handle. ! WARNING: Always keep the DR® SNOW THROWER discharge away from people, animals and objects which could be struck by debris. Adjustments Deflector Adjustment Adjust the deflector angle according to the distance the snow must be thrown. To adjust, loosen the knob, adjust to the desired angle then tighten knob securely. Skid Shoe Adjustment (...

Descargar ahora

Introduzca dos números de la imagen: