Votos - 1, Puntuación media: 5 ( )

Fabricar: Country Home Products Tamaño del archivo: 429.64 kb Nombre del archivo: Idioma del manual:

! WARNING: Always keep the DR® SNOW THROWER discharge away from people, animals and objects which could be struck by debris. Adjustments Deflector Adjustment Adjust the deflector angle according to the distance the snow must be thrown. To adjust, loosen the knob, adjust to the desired angle then tighten knob securely. Skid Shoe Adjustment (Figures 8 & 9) Adjust skid shoes in order to allow the required clearance (H) between the cutting edge and the surface, by loosening the 5/16" x 5/8" carriage bolts (item 2). On level paved surface or asphalt roadway: leave 1/16" to 1/8" clearance (H). On uneven or gravel surface, depending on gravel size: leave 1/2" to 5/8" clearance (H). Figure 8 DR® SNOW THROWER Safety, Operation & Maintenance Instructions 15 OPERATION General Preparation 1. Use a winter grade oil in your DR® ALLTERRAIN ™ MOWER. See the engine manufacturer's owner's manual. 2. Make sure that the auger operates freely. 3. Adjust the skid shoes so that the DR® SNOW THROWER runs level. 4. Make sure that the DR® SNOW THROWER is clear of snow before engaging the drive belt. ! WARNING: 1. Read this Operator's Manual carefully. Be thoroughly familiar with the controls and proper use of the equipment. Know how to stop the unit and disengage the controls quickly. 2. Never allow children to operate equipment. Never allow adults to operate equipment without proper instruction. 3. Keep the area of operation clear of people, animals and debris. 4. Clothing worn by the operator should be fairly tight and belted. Loose clothing should not be permitted because of the danger of getting into moving parts. Increasing Traction and Stability Use DR® Tire Chains for extra traction and stability. Call 1(800)DR-OWNER(376-9637) to order. Engine Speed ! CAUTION: Use only moderate engine speed when engaging the drive belt. Engaging the belt at high speed will shorten the clutch life. For maximum power, operate the engine at, or near, full throttle. Snow Removal Never use the DR® SNOW THROWER as a snowplow. Do not push the snow, let the SNOW THROWER work its way through deep drifts. For best results, raise the SNOW THROWER and remove a top layer of snow. A second pass will remove the remaining snow. If ground speed is too fast, the DR® SNOW THROWER may become overloaded and may clog. Maintain a ground speed suited for the job to be done. In heavy snow, take on only enough snow to work easily. Engage and disengage the clutch lever to reduce the ground speed to a level that will allow the engine to keep its full revolution. NOTE: Use full RPM power when removing wet, sticky snow. Low RPM power will tend to clog the chute. ! WARNING: Do not use your hands to unclog the chute. Use a short stick or board. Never attempt to clear clogged chute while the DR® ALL-TERRAIN™ MOWER engine is running. If the chute clogs, disengage the drive belt, wait for all movement to stop, apply the parking brake, shut off the engine and remove the spark plug wire before unclogging. NOTE: Run the DR® SNOW THROWER a few minutes after blowing snow to prevent freeze up of auger. DR® SNOW THROWER Safety, Operation & Maintenance Instructions OPERATION Snow Removal Methods When removing snow, do not use the DR® SNOW THROWER as a dozer blade to push snow. Let the DR® SNOW THROWER work its way through deep drifts. If the speed of your DR® ALL-TERRAIN™ MOWER is too fast, the DR® SNOW THROWER may become overloaded and clog. For best results, raise the DR® SNOW THROWER and remove the top layers of snow, or take a half-width pass. A second pass with the DR® SNOW THROWER will remove the remaining snow. IMPORTANT: Use full RPM power when removing wet, sticky snow. Low RPM power will tend to clog the chute. NOTE: In heavy snow, engage and disengage the clutch lever to reduce the ground speed to a level that will allow the engine to keep its full revolution. ! WARNING! To avoid serious personal injury, do not use hands or feet to unclog chute. Do not attempt to clear clogged chute of snow while DR® ALL-TERRAIN™ MOWER engine is running. If the chute clogs, disengage the drive shaft, shut off the engine, remove the spark plug wire and wait for all movement to stop, and then clear the snow from the chute. A definite pattern of operation is required to thoroughly clean an area of snow. These patterns will avoid throwing snow in unwanted places as well as eliminating a second ...

Descargar ahora

Introduzca dos números de la imagen: