Votos - 5, Puntuación media: 4 ( )

Fabricar: Ariens Tamaño del archivo: 1.75 mb Nombre del archivo: Idioma del manual:

7. Support Sno-Thro frame and housing. 2 3 OS0792 1 1. Pivot Pin 2. Housing Cap Screws 3. Belt Cover Figure 20 6 4 7 1. Traction Belt Idler 3 2. Cap Screw 3. Belt Finger 4. Traction Drive Belt 2 5. Attachment Belt Idler 8 6. Attachment Drive 1 Belt 7. Engine Sheave 8. Attachment Pulley 9. Attachment Idler 5 Adjustment Nut 9 OS3320 Figure 21 GB - 26 8. 8. CAUTION: Always support Sno-Thro frame and blower housing when loosening the cap screws holding them together. Never loosen cap screws while unit is in service position. frame (one on each side). Tip housing and frame apart on pivot pins (Figure 20). 9. Remove attachment drive belt from attachment pulley (hold brake away from belt). Install new attachment drive belt: 1. Place new attachment belt onto attachment pulley. 2. Tip housing and frame back together and secure with cap screws. 3. Place belt onto engine sheave. 4. Make sure engine sheave and attachment pulley align. If alignment is necessary, loosen attachment pulley set screws, reposition pulley and retighten set screws. 5. Reposition and secure belt fingers. IMPORTANT: Make sure belt fingers are 1/16 in. to 1/8 in. (1.6-3mm) from belt when attachment clutch is engaged. 6. Check adjustment. See Attachment Clutch/Brake. WARNING: AUGER / IMPELLER MUST STOP within 5 seconds when attachment clutch lever is released or unit damage or serious injury may result. 7. Reconnect chute crank and secure with spring clip. If equipped, reconnect remote cap deflector cable and/or electric chute wire harness. 1 2 3 4 5 Figure 22 6 OS0612 TRACTION DRIVE BELT REPLACEMENT NOTE: Housing and frame must be tipped apart and attachment drive belt removed from engine sheave in order to change traction drive belt. 1. Remove attachment drive belt (see Attachment Drive Belt Replacement). 2. Pull idler away from traction drive belt and remove belt from idler pulley, engine sheave and driven pulley (it may be necessary to turn engine pulley using recoil handle). NOTE: To gain clearance, engage traction clutch and if necessary pull back attachment idler arm clevis pin. 3. Install new traction drive belt onto attachment pulley and engine sheaves. 4. Replace attachment drive belt (See Replace Attachment Drive Belt). FRICTION DISC REPLACEMENT 1. Place unit into service position. 2. Remove bottom cover by removing four cap screws. 3. Place speed selector in first (1) position and depress traction clutch lever to hold friction disc and hub in position. 4. Remove cap screws from hub (Figure 22). 5. Release traction clutch lever, shift to third (3) position, and remove friction disc. 6. Secure new friction disc on hub with five cap screws and torque cap screws to 8-10 lbf-ft (10,6-13,3 N•m). 7. Replace bottom cover. 8. Adjust traction drive clutch (see Traction Drive Clutch Adjustment). 1. Cap Screw 2. Cotter Pin 3. Friction Disc 4. Shift Arm 5. Chain 6. Idler Hex Shaft GB - 27 BATTERY (924332, 505, 506, 508) BATTERY (924332, 505, 506, 508) 1. Place unit on a level surface and shut off engine. 2. Disconnect negative (-) cable first, then positive (+) cable. 3. Loosen wing nut and remove battery. Place battery on bench or other well ventilated place. 4. Connect positive (+) lead of charger to positive (+) terminal, and negative (-) lead to negative (-) terminal. 5. Charge the battery at two and a half amps for ten hours. 6. Reinstall battery into unit and connect positive (+) cable first, then negative (-) cable. Replacing Use U1R or U1L; 340 to 350 CCA @ 0°F type batteries. STORAGE WARNING: AVOID INJURY. Read and understand the entire Safety section before proceeding. SHORT TERM IMPORTANT: NEVER spray unit with high pressure water or store unit outdoors. Run with attachment clutch engaged a few minutes after each use to free unit of any loose or melting snow. Close fuel shut-off valve. Inspect unit for visible signs of wear, breakage or damage. Keep all nuts, bolts and screws properly tightened and know unit is in safe working condition. Store unit in a cool, dry protected area. LONG TERM Clean unit thoroughly with mild soap and low pressure water and lubricate (see Maintenance). Touch up all scratched painted surfaces. Remove weight from wheels by putting blocks under frame or axle. When storing unit for extended periods of time, remove all fuel from tank and carburetor (run dry). Refer to Engine Manual. SERVICE PARTS Order the following parts through your Dealer: Part No. Description 00036800 Stens Mix Hi-Temp Grease (3, 3 oz. cartridges) 21533500 Spark Plug (924122, 332, 505, 506, 508) 21533400 Spark Plug (924118, 121, 551) 07236200 Impeller Belt (924506) 07238332 Impeller Belt (924505) 07238400 Impeller Belt (924122, 332, 508) 07238500 Impeller Belt (924118, 121, 551) 07211200 Traction Belt (924118, 121, 122, 332, 508, 551) 07236100 Traction Belt (924505, 506) 00300300 Friction Disc 51001500 Shear Bolt Kit To obtain a complete parts manual, find your model and serial number. Then go to or call 1-800-678-5443. ACCESSORI...

Descargar ahora

Introduzca dos números de la imagen: