Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
Do not touch. • For the most efficient snow removal, remove snow immediately after it falls. • Discharge the snow downwind whenever possible. • Slightly overlap each previous path. • Set the skid shoes 1/4" below the shave plate for normal usage. The skid shoes may be adjusted upward (to lower the shave plate) for hard-packed snow. Adjust downward (to raise the shave plate) when using on gravel or crushed rock. • Be certain to follow the precautions found in the To Stop Engine section to prevent possible freeze-up. • Clean the snow thrower thoroughly after each use. 10 11 SECTION 6: MAKING ADJUSTMENTS WARNING: NEVER attempt to make adjustments while the engine is running, except where specified in the operator’s manual. Chute Directional Adjustment The distance snow is thrown can be adjusted by adjusting the angle of the chute assembly. Refer to the Chute Tilt Control in the Know Your Snow Thrower Section. Chute Directional Control And Support Bracket Adjustment (Model 724 STE) If the spiral at the bass of the chute directional control is not fully engaging with the notches in the lower chute assembly, the support bracket can be adjusted inward or outward as follows: • Loosen, but do NOT remove the hex nuts which secure the chute directional control support bracket to the snow thrower housing. See Figure 10. Figure 10 • Adjust the support bracket inward or outward so that the spiral is fully engaged in the notches on the chute before retightening the hex nuts. Skid Shoe Adjustment The space between the shave plate and the ground can be adjusted by raising or lowering the skid shoes. Refer to Skid Shoe Adjustment in Section 3 of this manual. Traction Control Adjustment Refer to the information found under the heading Final Adjustments in Section 3 of this manual to adjust the traction control. If you are uncertain that you have reached the correct adjustment, proceed as follows: WARNING: Drain the gasoline out of your snow thrower’s engine, or place a piece of plastic film under the gas cap to avoid spillage before making this adjustment. • Tip the snow thrower forward, allowing it to rest on the auger housing. • Remove the frame cover underneath the snow thrower by removing the six self-tapping screws. • With the traction control released, there must be clearance between the friction wheel and the drive plate in all positions of the shift lever. Figure 11 • With the traction control engaged, the friction wheel must contact the drive plate. See Figure 12. If adjustment is necessary: • Loosen the jam nut on the traction drive cable (see Figure 5). Adjust the cable as necessary. • Retighten the jam nut to secure the cable when correct adjustment is reached and reassemble. NOTE: If you placed plastic film under the gas cap, be certain to remove it before operating the snow thrower. Spiral Support Hex Nuts Bracket Shift Lever Ferrule Shift Arm Hairpin Clip Lower Shift Rod Clutch Rod Connector Upper Shift Rod Hairpin Clip Flat Washer 12 Figure 12 Auger Control Adjustment Refer to the information found under the heading Final Adjustments in Section 3 of this manual to adjust the auger control. Shift Rod Adjustment To adjust the shift rod, proceed as follows. • Remove the hairpin clip and slide the clutch rod connector up, to separate the upper shift rod from the lower shift rod. See Figure 10. • Place the shift lever into the sixth (6) position. • Rotate the shift arm clockwise (from the operator’s position) as far as it will go. • Thread the upper shift rod downward until the elbow on its lower end aligns with the hole found in the lower shift rod. • Reconnect the upper shift rod to the lower shift rod by reinserting the hairpin clip removed earlier and sliding clutch rod connector back down into place. IMPORTANT: Make certain to check for correct adjustment of the shift rod as instructed under the heading Final Adjustments in Section 3 of this manual, before operating the snow thrower. SECTION 7: MAINTAINING YOUR SNOW THROWER Lubrication WARNING: Disconnect the spark plug wire and ground it against the engine before performing any maintenance procedures. Engine Refer to the separate engine manual packed with your unit for all engine lubrication instructions. WARNING: When following instructions in the separate engine manual for draining oil, be sure to protect the frame to avoid oil dripping onto transmission parts. Electric Chute-Rotation Motor (Model 926 STE) The gear on the electric chute-rotation motor and the base of the discharge chute itself should be lubed with multi-purpose automotive grease once a season. See Figure 13. Auger Shaft At least once a season, remove the shear bolts on the auger shaft. Spray lubricant inside the shaft. See Figure 14. Also lubricate the plastic auger bearings at least once a season and grease the fittings on the end of the auger shaft with a standard grease gun. Gear Shaft Lubricate the gear shaft with 6-n-1 grease at least once a season or after every 25 hours of operation ...
Otros modelos de este manual:Quitanieves - 724 STE (5.47 mb)