Votos - 4, Puntuación media: 3.5
(
)
)
|
Resumen del manual
Machine has six forward speeds and one reverse. Refer to Figure 2.5. A WARNING A Release auger/impeller clutch control and make sure auger/impeller has STOPPED before rotating discharge chute, adjusting deflector or placing hands near auger/impeller._ 2.2.10. DISCHARGE CHUTE and DEFLECTOR ADJUSTMENT 1. Release auger/impeller control and wheel drive control levers to allow auger/impeller and ground speed to come to a complete stop. 2. Position the deflector to the desired location using deflector handle located on control panel. Rotate deflector handle counter clockwise to unlock. Push handle to raise or pull handle to lower the deflector. Rotate deflector handle clockwise to lock into position. 3. Rotate chute crank to position discharge chute in desired direction. Refer to Figure 2.5. 2.2.11. STOPPING - ENGINE, AUGER & WHEEL DRIVE Stop the auger/impeller and wheel drive by releasing the auger/impeller and wheel drive control levers. Stop the engine by moving the engine speed control to the stop position or removing the key from the switch. Always remove key from key switch before leaving machine unattended. Refer to Figure 2.7. Snow Thrower can be transported without engine running and transmission drag. 1. Remove hair pins and clevis pins from both wheel axles. Remove wheels from axle. Apply a liberal amount of axle grease to the axle to allow the wheel to rotate freely. 2. Slide wheel inward toward main case. 3. Reinstall clevis pins and hair pins into outer holes to prevent wheel from sliding off of the end of axle. Wheels will rotate freely on axle. IMPORTANT: If engine is started the wheel drive will not operate unless wheels and axle are reconnected. Reinstall clevis pins and hair pins into holes in the hubs of the wheels and through axle. See Figure 2.9. OUTSIDE FIGURE 2.9 2.2.12. FREE WHEEL MACHINE 10 Section 3 - MAINTENANCE 3.1 INTRODUCTION To retain the quality of the snow thrower, use only genuine SNAPPER replacement parts. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular snow thrower, always mention model and serial number. 3.2 SERVICE - AFTER FIRST 5 HOURS 3.2.1 CHECK AUGER DRIVE BELT 1. Visually check engine drive belt for cracking, fraying, severed or belt strands exposed. Replace belt before operating snow thrower. See Figure 3.1 FIGURE 3.1 3.2.2 CHECK WHEEL DRIVE BELT 1. Visually check wheel drive belt for cracking, fraying, severed or belt strands exposed. Replace belt before operating snow thrower. See Figure 3.2. 3.3 GENERAL LUBRICATION Lubricate machine as instructed before and after operation each season. 3.3.1. GEAR CASE, AUGER SHAFT and AUGER BEARING LUBRICATION 1. Before each season of operation, apply two shots of grease Snapper suggest using Benalene 900) from a grease gun into gear case. The grease plug for the gear case is located in front of the gear case. See Figure 3.3. 2. Before each season of operation, apply two shots of grease Snapper suggest using Benalene 900) from a grease gun into auger bearing. The grease fitting for the auger bearing is located on each end of the auger. See Figure 3.3. 3. Before each season of operation, apply two shots of general purpose grease from a grease gun into the auger shaft. The grease fitting for the auger shaft is located in the middle of each auger. Remove shear bolts and rotate auger to distribute grease evenly around shaft. Reinstall shear bolts and nuts. Tighten to 5 to 10 ft. lb. of torque. See Figure 3.3. FIGURE 3.3 3.3.2. GENERAL LUBRICATION After each season of operation, spread a small amount of grease on: The axle shafts for easy wheel removal. The discharge chute and mounting flange retainers for smooth rotation. FIGURE 3.2 11 Section 3 - MAINTENANCE 3.4 ANNUALLY (END OF EACH SEASON) Perform all maintenance as described in the maintenance schedule. 3.4.1. Engine Refer to engine owner’s manual for service instructions. 3.4.2. SparkPlug Refer to engine owner’s manual for service instructions. 3.5 STORAGE PROCEDURE Refer to the Engine Owner’s Manual for directions regarding engine storage preparations. Prepare the snow thrower for “end of season” storage as follows: 1. Drain fuel from fuel tank and let engine run until all fuel is out of the carburetor. 2. Disconnect and remove the spark plug wire away from spark plug before any other preparations are made! 3. Tape all openings closed to prevent spraying water into exhaust or air intakes during washing. 4. Tilt snow thrower up on its wheels and thoroughly clean the underside of the auger/impeller. 5. Lubricate all exposed metal with a light coating of oil to prevent corrosion. 6. Store the machine in a shed or other dry area, protected from weather. 3.6 MAINTENANCE and SERVICE PARTS MAINTENANCE and SERVICE PARTS Auger Drive Belt (Briggs Engines) 1-3937 Auger Drive Belt (Tecumseh Engines) 1-3939 Wheel Drive Belt (Briggs Engines) 1-3936 Wheel Drive Belt (T...
Otros modelos de este manual:Quitanieves - 10305E (1.2 mb)