Votos - , Puntuación media: ( )

Manual de usuario Bolens, modelo 933 SWE

Fabricar: Bolens
Tamaño del archivo: 2.62 mb
Nombre del archivo:

Idioma del manual:

El documento se está cargando, por favor, espere

Descargar ahoraCerca

El documento se está cargando, por favor, espere

Descargar ahoraCerca

While standing in the operator’s position (behind the 1. 2. 3. 4. 5. 6. DESCARGA A LA DERECHA DESCARGA A LA IZQUIERDA INCLINACION DEL CANAL HACIA ABAJO INCLINACION DEL CANAL HACIA ARRIBA CONTROLDIRECCIONALDELCANAL snow thrower), engage the auger control for a few seconds to clear any remaining snow and ice from the chute assembly. 1 sectiOn 4— cOntrOls and features Operation 5 Starting The Engine 1. Attach spark plug wire to spark plug. Make certain the metal loop on the end of the spark plug wire (inside the rubber boot) is fastened securely over the metal tip on the spark plug. 2. Make certain both the auger control and drive control are in the disengaged (released) position. 3. Move throttle control up to FAST position. Insert ignition key into slot. Make sure it snaps into place. Do not attempt to turn the key. NOTE: The engine cannot start unless the key is inserted into ignition switch. Electric Starter Determine that your home’s wiring is a three-wire grounded system. Ask a licensed electrician if you are not certain. WARNING! The optional electric starter is equipped with a grounded three-wire power cord and plug, and is designed to operate on 120 volt AC household current. It must be used with a properly grounded three-prong receptacle at all times to avoid the possibility of electric shock. Follow all instructions carefully prior to operating the electric starter. If you have a grounded three-prong receptacle, proceed as follows: 1. Plug the extension cord into the outlet located on the engine’s surface. Plug the other end of extension cord into a three-prong 120-volt, grounded, AC outlet in a well-ventilated area. 2. Rotate choke control to FULL choke position (for a cold engine start). NOTE: If the engine is already warm, place choke control in the OFF position instead of FULL. 3. Push the primer two or three times for cold engine start, making sure to cover vent hole in the center of the primer when pushing. NOTE: DO NOT use primer to restart a warm engine after a short shutdown. 4. Push starter button to start engine. Once the engine starts, release starter button. NOTE: Do NOT hold the button down for longer than seven (7) seconds at a time. Doing so may damage your engine’s electric starter. 5. As the engine warms, slowly rotate the choke control to the OFF position. If the engine falters, quickly rotate the choke control back toward FULL choke, and then slowly into the OFF position again. 6. When disconnecting the extension cord, always unplug the end at the three-prong wall outlet before unplugging the opposite end from the snow thrower. Recoil Starter 1. Rotate choke control to FULL choke position (cold engine start). NOTE: If the engine is already warm, place choke control in the OFF position instead of FULL. 2. Push the primer two or three times for cold engine start, making sure to cover vent hole in the center of the primer when pushing. NOTE: DO NOT use primer to restart a warm engine after a short shutdown. NOTE: Additional priming may be necessary if the temperature is below 15° Fahrenheit. 3. Grasp the recoil starter handle and slowly pull the rope out. At the point where it becomes slightly harder to pull the rope, stop pulling and allow the rope to slowly recoil. 4. Pull the starter handle with a firm, rapid stroke. Do not release the handle and allow it to snap back. Keep a firm hold on the starter handle and allow it to slowly recoil. 5. As the engine warms, slowly rotate the choke control to the OFF position. If the engine falters, quickly rotate the choke control back toward the FULL choke position, and then slowly into the OFF position again. NOTE: Allow the engine to warm up for a few minutes after starting. The engine will not develop full power until it reaches operating temperatures. Stopping The Engine Run engine for a few minutes before stopping to help dry off any moisture on the engine. 1. Move throttle control to STOP position. 2. Remove the ignition key and store in a safe place. 3. Wipe all snow and moisture from the area around the engine as well as the area in and around the drive control and auger control. Also, engage and release both controls several times. To Engage Drive 1. With the throttle control in the Fast (rabbit) position, move shift lever into one of the six forward (F) positions or two reverse (R) positions. Select a speed appropriate for the snow conditions and a pace you’re comfortable with. NOTE: Use slower speeds in higher snow and/or until you are familiar with the snow thrower operation 2. Squeeze the drive control against the handle the snow thrower will move. Release it and drive motion will stop. CAUTION: NEVER move the shift lever without first releasing the wheel drive control. Doing so will cause premature wear on the drive system’s friction wheel 3. To turn the snow thrower to the left or right, squeeze the respective wheel steering control. Refer to Figure 4-1. To Engage Augers 1. To engage the augers and start throwing snow, squeeze...