Votos - 2, Puntuación media: 4.5 ( )

Fabricar: Simplicity Tamaño del archivo: 1.73 mb Nombre del archivo: Idioma del manual:

The above parts group applies to the following Mfg. Nos.: 1694589 - 9560E 1694597 - 9560M © Copyright2005 Simplicity Manufacturing, Inc. All Rights Reserved. 19 TP 400-4155-01-LW-S Auger and Impeller Group NOTE: Unless noted otherwise, 985466 use the standard hardware torque specification chart. End of hub to be flush with end of rolled down shaft (Ref. 9). Torque to 30 -34 ft-lbs. 40 - 46 Nm. Impeller to be positioned against bearing before tightening set screw. Marked side of worm gear must contact against left thrust washer to assure proper gear mesh. Auger assembly stamped "R". Auger assembly Torque to 18-21 ft-lbs. 24 - 28 Nm. Apply grease until it appears at ends of auger assembly (2 places). Torque to 9 - 11 ft-lbs. 12- 15 Nm. 1 2 3 4 5 67 89 10 12 13 14 15 16 17 18 19 20 21 22 23 24 25 28 27 2 10 10 6 26 14 18 11 29 stamped "L". The above parts group applies to the following Mfg. Nos.: 1694589 - 9560E 1694598 - 1060M 1694590 - 1060E 1694599 - 1170M 1694591 - 1170E 1694600 - 1280M 1694592 - 1280E 1694601 - 1390M 1694593 - 1390E 1694597 - 9560M © Copyright2005 Simplicity Manufacturing, Inc. All Rights Reserved. 20 TP 400-4155-01-LW-S Auger and Impeller Group REF NO PART NO. DESCRIPTION QTY. 1 1679293 1 PULLEY, w/Hub 2 1928721 2 SCREW, Set Square Head Cup Point, 5/16-18 x 1/2 G8 3 1612187A 1 IMPELLER ASSEMBLY 4 1960474 1 SCREW, Set Square Head Cup Point, 3/8-16 x 1/2 G8 5 1612093 1 SEAL, Oil 1/4" Thick 6 1612149 2 BUSHING, 377/500 ID x 1-1/10 OD x 1-1/100 LG Powerdered Metal 7 1612127 1 COLLAR, Thrust 3/4 LG 8 2836098 1 PIN, Drive Lock Type A 3/16 x 1-1/2 9 1612129 1 SHAFT, Worm 18-1/10 LG 10 2818312 3 KEY, Woodruff, 47/250 x 5/8 11 1612111 1 TUBE, 9/10 OD 39/50 ID, 7-1/2 LG 12 1612142 1 GEAR, Worm 1-3/8 LG 13 2168111 1 WASHER, Thrust 14 2118118 2 SEAL, Oil, 1/4" Thick 15 1923358 6 LOCKNUT, Hex, 1/4-20 Qauntity 8 used on 38 in. Models 16 1612137 1 CASE, Gear R.H. 17 1612124 1 GASKET, Gear Case 18 2118315 2 WASHER, Thrust 19 1612117 1 SHAFT, 16 LG Auger 3 Holes 20 2830246 1 KEY, Woodruff 1/4 x 3/4 21 1612141 1 GEAR, Worm 7/8 LG 22 1612136 1 CASE, Gear L.H. 23 1668971 1 PLUG, Pipe, Tapered, 1/8 Used on 38 in. Models 24 1960346 6 CAPSCREW, Hex Head, 1/4-20 x 2-1/4 G5 Quantity 4 used on 38 in. Models 25 1668344 2 PIN, Flat Head Drilled 26 1918447 2 PIN, Cotter 47/50 x 3/4 27 1718782A 1 AUGER ASSEMBLY, L.H. 9-1/2 LG Used on 24 in. Models 27 1718784A 1 AUGER ASSEMBLY, L.H. 11-1/2 LG Used on 28 in. Models 27 1718786A 1 AUGER ASSEMBLY, L.H. 13-1/2 LG Used on 32 in. Models 28 1718783A 1 AUGER ASSEMBLY, R.H. 9-1/2 LG Used on 24 in. Models 28 1718785A 1 AUGER ASSEMBLY, R.H. 11-1/2 LG Used on 28 in. Models 28 1718787A 1 AUGER ASSEMBLY, R.H. 13-1/2 LG Used on 32 in. Models 29 2821133 2 FITTING, Lube 1/4 Drive, No Check Ball Footnotes The above parts group applies to the following Mfg. Nos.: 1694589 - 9560E 1694598 - 1060M 1694590 - 1060E 1694599 - 1170M 1694591 - 1170E 1694600 - 1280M 1694592 - 1280E 1694601 - 1390M 1694593 - 1390E 1694597 - 9560M © Copyright2005 Simplicity Manufacturing, Inc. All Rights Reserved. 21 TP 400-4155-01-LW-S Auger Housing and Chute Group - 38" Models NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Coat top and bottom of chute ring with grease. Scraper blade should be on inside of housing. When installing cable, make sure it does not come into contact with muffler. Plastic washer (Ref. 3) goes between chute and deflector. See Handles and Controls group for Wiring Harness. Mount cable bracket (Ref. 23) on right hand side of handle using shift control bracket hardware. 2 4 5 12 15 16 18 24 17 19 23 21 22 50 29 30 31 32 37 38 29 39 40 41 51 2 44 43 42 46 47 20 45 3 36 1 48 49 33 35 34 10 25 27 26 28 11 14 1235 7 8 9 6 986720 The above parts group applies to the following Mfg. Nos.: © Copyright 2 0 0 5 Simplicity Manufacturing, Inc. All Rights Reserved. 22 1694593 - 1390E 1694601 - 1390M TP 400-4155-01-LW-S Auger Housing and Chute Group - 38" Models PART NO. REF NO QTY. DESCRIPTION 1 1960001 3 SCREW, Hex Washer Head Pastite, 10-14 x 5/8 2 1931333 10 CARRIAGE BOLT, 5/16-18 x 3/4 G5 3 2860210 1 WASHER, Special, 97/250ID x 1-3/25OD x 3/100 Thick 4 1919326 1 WASHER, 5/16 5 1919438 1 NUT, Hex Lock ESNA Light, 5/16-18NC-3B 6 1933896 2 NUT, Hex Nylon 10-24 7 1725427C 1 BRACKET, Mounting Switch Bottom 8 1725426C 1 BRACKET, Mounting Switch Top 9 1960725 1 SCREW, 10-24 x 1.75 10 1724205 1 SWITCH, Rocker Chute 11 1725696 1 BOOT, Rocker Switch 12 1727194C 1 CHUTE AND DEFLECTOR ASSEMBLY, Riveted, w/Pigtail 13 1702219 3 SPACER, Heat Treated 14 1960126 2 NUT, Push Pal, 1/4" Diameter Stud Capped 15 1611945 1 ROD, 5/16" Diameter, Spring Guide 16 1611939 1 SPRING, Complete 17 1720446 1 CABLE AND KNOB ASSEMBLY, Chute (Includes Ref. No. 18, 19, 20, 21 & 22) 18 1611989 1 BOOT, Bellows 19 1719140 1 COLLET 20 1719139 1 SEAL, Rod 21 1719138 1 KNOB 22 1960600 1 SCREW, 8-32 23 1726411A 1 SUPPORT, Cable 24 2825094 1 TIE, Self Locking 25 2860664 3 SCREW, Hex Sems Washer, 1/4-20 x 7/8...

Descargar ahora

Introduzca dos números de la imagen: