Iniciar sesión:
Votos - 2, Puntuación media: 3 ( )

Manual de usuario Gravely, modelo 20982

Fabricar: Gravely
Tamaño del archivo: 3.38 mb
Nombre del archivo:
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


See figure 6.0-2. 5. Lower the snowblower to the ground. 6. Put the RANGE selector in the LO position. I - Discharge Chute Crank Figure 6.0-2. 7. Engage the PTO. 8. Move the throttle lever to the FAST position. 9. Put the GEAR selector in the 2 position. NOTE: When going through the snow for the first time, a full width passage must be cut. The forward speed must be slow enough to permit the snow to go through the discharge chute without being stopped. 10. Put the Direction Control Lever in the forward position and make the first passage through the snow. WARNING: The snowblower auger or impeller can be stopped by too much ice, snow or debris while the engine is still giving power to the snowblower. Severe injury to the person can be caused when cleaning the snowblower while the engine is running. NEVER CLEAN THE SNOWBLOWER WITH THE ENGINE RUNNING. 11. On the next and remaining passages, cut as much snow as will go through the discharge chute without being stopped. 12. If the reel stops turning while the fan continues to turn, disengage the PTO, stop the engine and tighten the nuts on each end of the reel shown in figure 6.0-3 to a torque of 85 ft. lbs. (115 Nm). 1 - Reel 2 – Nut Figure 6.0-3 7.0 MAINTENANCE After Each Use 1. Inspect all nuts, bolts and other fasteners to make Insp sure they are tight and replace any that are gone. 2. Inspect the reel, fan, skids and wearstrip for damage and replace if damaged. 3. Put lubricant on the wire rope where it goes through the guide tubes. Use tractor engine lubricant. 4. Put lubricant in the holes where the fan housing connects to the reel housing. Use tractor engine lubricant. 5. Add multi-purpose grease to the grease fitting on the universal joint until grease comes out the end of the universal joint 6. tube. 8.0 STORAGE 1. Clean the Snowblower. 1. Check the gear housing lubricant level by removing the pipe plug shown in figure 8.0-I. The lubricant level is correct when the lubricant is at the bottom of the pipe plug hole. Add SAE 90W EP gear lubricant when the level is low. Install the pipe plug and tighten it. 2. To prevent rust, put paint or grease on any area where the paint has been removed. 1 --Gear Housing 2 - Pipe Plug Figure 8.0-1 GRAVELY ATTACHMENT LIMITED WARRANTY This Limited Warranty is issued by Gravely Division, McGraw-Edison Company, and consists of the following terms: 1. Only the original purchaser of new Gravely manufactured attachments is covered by this Warranty. 2. This Warranty covers repair or replacement of parts manufactured by Gravely which are defective in material or workmanship. Gravely will pay for parts and labor only. 3. The Warranty starts the date of purchase and lasts for NINETY (90) DAYS for attachments used in Roofer applications, and TWELVE (12) MONTHS for products used in all other applications. 4. Some components of Gravely attachments are not covered by the Gravely Warranty. These components are covered by the original manufacturer's warranty, which is included with the product. They are: a) Engine - Honda b) Tires - Goodyear and Armstrong 5. To obtain warranty service on Gravely attachments including components not manufactured by Gravely. use this procedure. a. Notify the Gravely dealer from whom you purchased the attachment. b. If you have moved and it is not convenient to notify the selling dealer, notify the nearest Gravely dealer. You should supply this dealer with a copy of the bill of sale as proof of the date of purchase. c. Make arrangements to have the attachment delivered to the dealer (refer to paragraph 6(a) below. d. It you have any questions concerning the Gravely Limited Warranty, they should be referred to Gravely Division McGraw-Edison Company One Gravely Lane Clemmons, NC 27012 Attn: Manager of Customer Services e. Warranty service on Gravely attachments must be performed by an authorized Gravely dealer or Gravely factory branch. 6. This Warranty does not cover the following: a. Transportation between owner's home or place of business and the dealership. If the dealer provides the transportation of the attachment, he will charge the owner his usual rate for such service. b. Normal maintenance services and normal replacement of items such as spark plugs, belts, oil, oil filters, air filters, and mower, plow or cultivator blades. 7. GRAVELY MAKES NO OTHER EXPRESS WARRANTIES. ANY IMPLIED WARRANTIES, INCLUDING WARRANTIES AS TO MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE PERIOD SET OUT IN PARAGRAPH 3 ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE STATEMENT MAY NOT APPLY TO YOU. 8. GRAVELY SHALL HAVE NO RESPONSIBILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE BREACH OF ANY WARRANTY, INCLUDING, BUT NOT LIMITED TO, INCONVENIENCE, RENTAL OR PURCHASE OF REPLACEMENT PRODUCTS, LOSS OF PROFITS OR COMMERCIAL LOSSSOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE...

Otros modelos de este manual:
Quitanieves - 20979 (3.38 mb)
Quitanieves - 20980 (3.38 mb)
Quitanieves - 20981 (3.38 mb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría